Bearing Buddy Bearing Protectors For a Malone Low Max MPG595 Trailer

Question

Question:

What bearing buddy is made for malone low max trailer mgp595

asked by: Harold W

1

Helpful Expert Reply:

The Bearing Buddy Bearing Protectors # BB1980A-SS are the correct size for the Malone Low Max MPG595 trailer. These are constructed of stainless steel and comes with the Auto-Check feature so you can visually see when you need to add grease to the hubs.

expert reply by: Bud M

1

Answer 1

Yes, the Trailer Idler Hub Assemblies #TA88545-2 are two 5 on 4-1/2" bolt pattern idler hubs that will fit the CE Smith Trailer Axle Beam with EZ-Lube Standard Spindles #CE33201GA. These will allow for you to mount a 15" wheel and…

view full answer...

Answer 2

According to Malone, the correct replacement bearings for your Malone MicroSport Trailer #MAL25FR are the #L44649. If you would like the bearing kit that includes the inner and outer bearing, along with the grease seal and races, then we have the…

view full answer...

Answer 3

The Malone Low Max trailer has a removable hub, so you'll be able to pull it to access and remove the bearings; we've actually done a helpful video that walks through the process of removing, inspecting and re-packing your bearings.…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference.…

view full answer...

Bearing Buddy Bearing Protectors For a Malone Low Max MPG595 Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching