Wire Gauge Size Needed For The SmartPlug RV Power Inlet And Connector

Question

Question:

I see it says you can just cut your old plug off and install a new female smart plug that comes with the kit. On the back is a water proof strain relief. I’m wondering what size of cable this strain relief can accommodate? Also what size wire the plug terminals can accommodate?

asked by: William R

0

Expert Reply:

The connector for the SmartPlug RV Power Inlet and Connector # SM87FR is designed to work with three 10AWG wires along with their casing. The port is designed for 10AWG wire as well but can handle 8AWG.

expert reply by: Kevin C

0

Answer 1

Yes, in order to set your trailer up for use with shore power you will first need an AC distribution panel. For this, I recommend a Progressive Dynamics Series AC Distribution Panel. In order to bring power into the panel you will also need a power…

view full answer...

Answer 2

The 15,000 Btu Furrion air conditioner is what I would recommend and what I have on my trailer. Since it is an enclosed trailer I'm guessing you want the manual distribution box. You can choose from the following based on color: -Furrion Chill HE…

view full answer...

Answer 3

Aside from the six 15A or GFCI power receptacles (5 interior and 1 exterior) and the breakers/fuses, we have all the parts you need to complete your project. For the power inlet on the outside of your horse trailer you can use the Epicord 30 Amp…

view full answer...

Answer 4

The 1" Long Black Torx Wall Liner Screw #WLS100 is the best option for the plywood installation. These screws are fine thread and made for metal studs. They have a tapping edge but often a starter or pilot hole should be drilled. You can then…

view full answer...

Answer 5

Yes, the dimensions of the 30 Amp SmartPlug RV Power Inlet and Connector, found in Gray #SM87FR or White #SM77FR is as follows: Receptacle - 3.25" wide x 4.5" tall x 3.75" long (or deep) Plug - 3" wide x 3" tall x 4"…

view full answer...

Answer 6

I sure can; I have added a photo for you with the dimensions of the mounting hole for the 50 amp SmartPlug inlet and connector. This comes in your choice of three different colors, and the dimensions are the same for each: - Black: SmartPlug RV Power…

view full answer...

Answer 7

Yes, your 2019 Subaru Crosstrek with a manual transmission is flat-towable. You'll need a few things to do this. First is a base plate kit. For that you'd want the Roadmaster Direct Connect kit part #RM-52927-5 which is custom fit for your…

view full answer...

Answer 8

We have what you need, I have a tankless water heater linked below that will work: **Fogatti RV Tankless Water Heater - Gas - Automatic Pilot - 41,800 Btu - White #LSB64FR. **Camco RV Water Heater Temperature and Pressure Relief Valve - 1/2"…

view full answer...

Answer 9

I suggest you first take some measurements to verify fitment. However, specs available to me show dimensions of, 16" W x 12-1/2" H x 18"D. For the Fogatti RV Water Heater #LSB64FR, overall dimensions are 14-3/8L x 15W x 15D. The access…

view full answer...

Answer 10

I believe what you're looking for is the: -Replacement Pitch Arm Assembly for Solera XL 63" Flat Awning Support Arm #LC67VR. This arm measures 33" long, and is a direct replacement for the Solera XL 63" long flat awning support…

view full answer...

Wire Gauge Size Needed For The SmartPlug RV Power Inlet And Connector

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching