Can I Use the 2-5/16" Curt Rockerball with My Weight Distribution System?

Question

Question:

Hi I was just wondering if you can use the 2 5/16” rocker ball on a weight distribution hitch for a camper trailer?

asked by: Will

0

Expert Reply:

I have an answer for you. Unfortunately, we confirmed with Curt that the 2-5/16 Rockerball models # C29FR and # C82KR cannot be used with a weight distribution system.

If you need a 2-5/16 inch ball, I recommend the Draw-Tite # 63847 if your weight distribution system requires a 1-inch diameter shank or the Draw-Tite # 63840 if your system requires a ball with a 1-1/4 inch diameter shank.

expert reply by: Bob C

0

Answer 1

The Curt RockerBall Shock Absorbing 2-5/16" Hitch Ball - 1-1/4" Diameter Shank - Chrome - 12K #C29FR does not fit weight distribution heads because the base of the ball is meant to fit the rectangular platform. If you remove that part of…

view full answer...

Answer 2

The Curt RockerBall Shock Absorbing 2" Hitch Ball part #C40047 will not work with a weight distribution system because the flange that gets wedged between the platform and base that stops the unit from rotating will not fit over the shank on a…

view full answer...

Answer 3

Good question. I checked with Curt because I haven't had this come up yet but unfortunately no, the RockerBall, part #C29FR, cannot be used with a weight distribution system. Looking at your pictures I think you have a Blue Ox SwayPro system,…

view full answer...

Answer 4

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 5

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 6

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

It does appear you are going to be able to flip the axles on your 2023 Northern Spirit 2145RBX using 2 of the Dexter Trailer Springs Over-Under Conversion Kits #K71-384-00. I will warn you Kalvin this will raise the height of your camper roughly…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

view full answer...

Answer 11

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...

Can I Use the 2-5/16" Curt Rockerball with My Weight Distribution System?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching