Does Appearance Panel Get Reinstalled on 2018 Toyota RAV4 w/ etrailer Trailer Hitch
Question:
Hi, I am interested in Item # e98864, a hitch for a 2018 RAV4. I watched the install video, which was helpful. I do have one question, at 2:30 in the video, it shows removal of a plastic tray on the drivers side prior to installation. It does not show the tray being reinstalled after the hitch is in. Does the plastic tray get bolted back in or does it need to be cut or modified after the hitch is installed? Thanks.
asked by: Keith R
Expert Reply:
Good question, and the panel you are referring to does get reinstalled on your 2018 Toyota RAV4 when installing the etrailer Trailer Hitch Receiver # e98864.
You will trim a small section of it (as shown in the cut out below), and the same push pins and nut that were holding it in will be used to reinstall the panel. So just be a bit careful with the push pins when prying them out and after trimming the small section you can put it back on after the # e98864 in fully installed.
And in the interest of being thorough I also wanted to mention that if you plan to use the hitch for towing with your 2018 RAV4 and need a wiring harness, the correct fit is the T-One Vehicle Wiring Harness # 118578.
Products Referenced in This Question
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Visible Cross Tube
- etrailer
more information >
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Trailer Wiring
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: My Trailer Hitch Doesn't Fit
- Shop: Roof Rack
- Video: Tow Ready Trailer Wiring Harness Installation - 2018 Toyota RAV4
- Video: Curt Trailer Hitch Installation - 2016 Toyota RAV4
- Video: Trailer Hitch Installation - 2010 Toyota RAV4 - Curt
- Video: Trailer Hitch Installation - 2011 Toyota RAV4 - Curt
- Video: Master Lock Pivot Lock Hitch Pin Review
- Video: etrailer Class III Trailer Hitch Installation - 2011 Toyota RAV4
- Search Results: hitch pin
- Shop: Master Lock Pivot Lock Hitch Pin for 2" Hitches - 5/8" Diameter - Stainless Steel
- Q&A: Does Installation of etrailer Trailer Hitch Receiver on 2014 Toyota RAV4 Require Fascia Trimming
- Q&A: Does etrailer.com Hitch E98864 Fit 2009 Toyota RAV4
- Q&A: Hitch for Thule T2 Pro XT with Toyota 2018 RAV4 XLE
- Q&A: Fit of Thule TH934XTR Hitching Post Pro on 2011 Toyota Rav4 w/ Curt C13149 Class III Trailer Hitch
- Shop: Nylon Tube Brush - 1/2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: etrailer.com Trailer Hitch Installation - 2015 Toyota RAV4
- Search Results: timberline towers
- Q&A: Removing and Installing New Replacement Rubber Strap Kit for Yakima TimberLine Towers
- Shop: Floor Mats
- Search Results: sks lock
- Search Results: loctite
- Search Results: y07204
- Q&A: Is Loctite Required When Installing a Trailer Hitch