Can I Use My Current Atwood Jack System with the HappiJac # LC736515-ELKIT?

Question

Question:

I have a Lance Camper with Atwood electric Jacks, I want to replace only jacks with HappiJac Electric Jacks 36-1/2 11,200, I will rewire the Happijac connects to atwood connections and use the atwood controller. Do you see any problem with doing this

asked by: Thomas B

0

Expert Reply:

I went ahead and reached out to both my tech and my parts expert from Lippert (the makers of Happijack), and they unfortunately confirmed that the HappiJac Electric Truck Camper Jack System - 36-1/2" Lift # LC736515-ELKIT requires the specific components included with the installation hardware. Using your Atwood setup can possible damage the control panel of the HappiJac system (if it even works at all). The best and safest route is to completely replace your setup with the complete HappiJac system.

expert reply by: Bob C

0

Answer 1

The HappiJac Electric Truck Camper Jack System part #LC736515-ELKIT that you referenced does come with the parts needed to replace your manual jacks with electric jacks. You'd need to remove the brackets you have now and install what comes…

view full answer...

Answer 2

The HappiJac Electric Truck Camper Jack System #LC736515-ELKIT is the current replacement for the HappiJac 4800 series jacks. This is an upgrade as it includes the electric motor versus the HappiJac Manual Truck Camper Jack System #LC736515-4 which…

view full answer...

Answer 3

We do have an electric option available that may work for you. The HappiJac Electric Truck Camper Jack System #LC736514-ELKIT will have a higher capacity of 8,800 pounds, but does only have 34-1/2 inches of lift. This will also include the mounting…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 10

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Can I Use My Current Atwood Jack System with the HappiJac # LC736515-ELKIT?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching