Bike Frame Cradle to Use as Replacement for Yakima 8780023

Question

Question:

I am looking for anti sway cradle # 8780023 for an old Yakima Full Swing 4 # 8002403. Will this cradle fit the rack? Thanks!

asked by: Sean C

0

Expert Reply:

Since the frame cradles you are looking for are designed to fit a 1-1/4 inch arm we have a solution but it's not the # Y8890158 which fits a different size. Instead you could use the Hollywood Racks # HR750-P and you'd be set.

expert reply by: Jameson C

0

Answer 1

You can try hairspray, but if the cradles are new they shouldn't move that easily. You can also put a single layer of electrical tape around the arms of the rack to add space and friction to the cradle assembly. What bike rack did you install the…

view full answer...

Answer 2

When replacing the Replacement Hold Fast Cradle for Thule Archway and Apex Bike Racks #7521513002, the previous cradles may have screws in which case you can just reuse them and be done with it. If it happens to have rivets, which you can look on…

view full answer...

Answer 3

For the Yakima SwingDaddy 4 Bike Rack, you will want the Replacement Wrench #8890285 and I believe you are looking for either the Replacement hitch pin #889-0231 or Replacement Speed Knob and Wedge Assembly #8880508. If you need anything else, let me…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 10

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Bike Frame Cradle to Use as Replacement for Yakima 8780023

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching