Stabilizer Pad For 12 Inch Octagon RV Jack Plate

Question

Question:

Do you guys carry Jack pads like the SnapPad or similar that fit 12” Hexagon Jack Feet Thanks...

asked by: Don

0

Expert Reply:

I have a solution for you.

After talking with my contact at RV Snap Pad and researching this foot pad you have. They do not make a snap on pad that fits this type of application.

The lips on your foot are to tall and they do not have anything that can fit on them.

You will need to go with a stabilizer pad like the Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2 # SC57VR.

expert reply by: David B

0

Answer 1

Yes, you could use the Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2 #SC57VR along with Andersen's Jack Block or with the Stromberg Carlson Base Pad Extreme for RVs and Trailers - 6,000lbs -…

view full answer...

Answer 2

SnapPads like part #SP54FR4 are not able to be used under the Stromberg Carlson Base Pad Extreme #SC33VR as they wouldn't properly fit the base of the base pads. The base pads can be used under the SnapPads to help clear up large gaps though. You…

view full answer...

Answer 3

The SnapPad Jack Stand Pads for Class A Motorhome - 8" Round and 10" Round Jack Feet part #SP34FR64 is exactly what you need for the 2020 Tiffin Phaeton Motorhome with 2-8" hydraulic jack feet and 2-10" hydraulic jack feet.

view full answer...

Answer 4

The Snap Pad Jack Pad for Camper Jacks w/5-1/2" Round Feet Item #SN97FR is going to be too big to snap on to your 5.278" foot. What you can do instead is use the Stromberg Carlson RV Jack Pads for RVs and Trailers - 9" Long x 6"…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 11

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have the…

view full answer...

Answer 12

While I have no way to see exactly what leveling system you have on your 2006 Tiffin Phaeton 35DH, I was able to find information on a forum showing someone who did confirm the SnapPad HiWay 10 Jack Pads for HWH and Atwood Leveling Systems w/…

view full answer...

Stabilizer Pad For 12 Inch Octagon RV Jack Plate

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching