Rivet Size to Use with Replacement Black UWS Logo Badge # UWS99FR

Question

Question:

What size are the rivets supposed to be

asked by: Jody A

0

Expert Reply:

The holes of the Replacement Black UWS Logo Badge # UWS99FR are 3/16 inch so going with rivets that diameter or slightly smaller would work well.

expert reply by: Jameson C

0

Answer 1

The Replacement Black UWS Logo Badge #UWS99FR normally installs with rivets or nuts and bolts. I am sure there is a way you could use an adhesive to install it but it's hard to say exactly what would be the best route for that.

view full answer...

Answer 2

To remove the current gas strut on your UWS toolbox you will simply need to take a flathead screwdriver and pop the clip on either head. This will allow you to pull the strut right off. Once the strut is removed you just have to push the ends of the…

view full answer...

Answer 3

In regards to a UWS Truck Bed Toolbox, if the box is locked and there is no key then you have two options. If you know the key number (it may be stamped onto the lock/latch) then you can order a replacement key like the Replacement Key for UWS…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Rivet Size to Use with Replacement Black UWS Logo Badge # UWS99FR

Product Page this Question was Asked From

Continue Researching