Compatible Battery Types For The Go Power 2000 Watt Pure Sine Wave Inverter Charger

Question

Question:

I have 4 Battle Borne Lithium Batteries and I wanted to make sure the IC 2000 Inverter/Converter is compatible to charge them. Thank you.

asked by: John R

0

Expert Reply:

The Go Power Industrial Pure Sine Wave Inverter Charger # 34280055 you referenced is compatible with sealed/gel, AGM, flooded/wet cell, and lithium batteries so you'll have no issues using it with your Battle Born lithium batteries. The included fixed-mount remote will allow you to select the correct charging profile for your battery type.

expert reply by: Kevin C

0

Answer 1

With a transfer switch like the Go Power Automatic Transfer Switch #342GPTS you would have to use a second Transfer Switch #PD5110010Q to connect 2 of the three sources. Your shore power cord could also be used with a separate plug in for a…

view full answer...

Answer 2

Yes the double lip grease seals in the TruRyde Bearing Kit, #BK3-300, will work on your horse trailer axle as long as it is the correct size seal for your spindle. I have attached a photo showing how to measure the inner and outer diameter of the…

view full answer...

Answer 3

Thank you for the photo; I contacted Lippert with the information you gave me and they told me that you will need Grease Seal #GS-2250DL. This seal has a 2.250" inner diameter and 3.376" outer diameter; the seal you asked about, part…

view full answer...

Answer 4

The correct bearing kit you will need is the part #BK3-300 that you referenced. This comes with bearings you have as well as a grease seal with the same inner diameter of 2.250 and outer diameter of 3.376 that your 2250D has.

view full answer...

Answer 5

The Provider ST235/85R16 Radial Tire with 16" Viking Aluminum Wheel #A16RGBML is compatible with either 1/2"-20 or 9/16"-18 wheel bolts, the recommended torque specification will depend on which of these two your hub uses. The tire,…

view full answer...

Answer 6

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 7

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 8

The remote and the remote cable of the Go Power Industrial Pure Sine Wave Inverter Charger #34275013 is included with it. I attached a picture that shows both the cable and the remote.

view full answer...

Answer 9

The Progressive Dynamics Replacement Section #PD4655V does have a jumper to change the charging profile to lithium compatible. You'll simply need to move the black jumper over from the WIZ side to the LI side.

view full answer...

Answer 10

It sounds like you already have the Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers #GP37MR with the Go Power MPPT Solar Charge Controller #GP72RR. The Remote Display for Go Power MPPT #GP37MR actually uses a bluetooth app as…

view full answer...

Answer 11

This is a pretty common issue as the 12 volt accessory/charge circuit is not always active on vehicles with OEM 7-ways. The solution is to run 10 gauge wire like part #10-1-1 (sold by the foot) through a breaker like part #9510 between the 1:00 pin…

view full answer...

Answer 12

The difference between the 1621 and the 1621SHD is weight capacity and how many bolts is required to mount it. The 1621 uses 4 bolts for mounting. The 1621SHD requires all 6 bolts to be used.

view full answer...

Compatible Battery Types For The Go Power 2000 Watt Pure Sine Wave Inverter Charger

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching