Is MORryde Rubber Suspension Kit SRE4000 For 35 Axle Spacing a Good Option

Question

Question:

Hello, I have a 2022 Arctic Fox 28-5C fifth wheel with tandem 7K Dexter axles w/stock equalizers, 35” spacing. Was thinking about upgrading to MORRyde SRE 4000 but am concerned about delamination and other failures I have read about on various forums. can you confirm whether or not the Morryde sre4000 are having failure issues or are they a good option? I am looking for guidance on upgrading the equalizers, thank you.

asked by: Steve C

0

Expert Reply:

All of the feedback we have had for the MORryde SRE4000 kit has been positive; I have not had anybody come back to me with any type of issue, and I also went and looked through our reviews on this and even similar kits and equalizers and haven't found any issues. Since you mentioned 7k axles with 35" spacing the SRE4000 kit you are referring to is the following part number:

- MORryde AllTrek 4000 Equalizers for Tandem Axle Trailers - 35" Wheelbase # MR29DR

And while you can use your existing shackle links as well, it is a good idea to upgrade that hardware along with the equalizers for the most durable set up, which you can do with the MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 3-1/8" Long Shackle Straps # MR76ZR.

expert reply by: Kyle S

0

Answer 1

Yes, it is possible. The SRE4000 is quite a big upgrade over the CRE3000. The SRE4000 provides more suspension travel at 4" instead of 3" and better road shock absorption. The axle capacity won't matter but it is important…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The correct MORryde Rubber Suspension Upgrade for Triple Axle Trailers for a 2018 Heartland Road Warrior 429 is part #MR77ZR which comes with the equalizers, braces, and everything you need to install them. If you want new shackles and wet bolts…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures 40-1/2" long x 29" wide x…

view full answer...

Answer 6

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have the…

view full answer...

Answer 7

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

Answer 8

The Clearsource Ultra RV Water Filter System w/ VirusGuard #CS87FR weighs 34.125 lbs.

view full answer...

Answer 9

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...