Installing Draw Tite-Hitch On A 2021 Acura RDX
Question:
I need a hitch for my 2021 Acura RDX and think I will buy the 36114 Draw-Tite that you have. I see you have installation videos for a lot of the hitches for other vehicles. Are the instructions that come with the hitch clear, can I install easily enough myself or do I need to hire a mechanic?
asked by: Quentin
Expert Reply:
The Draw-Tite Trailer Hitch Receiver, # 36114 is a great option for your 2021 Acura RDX . You are correct that we don't currently have a video for installing this hitch, on a 2021 model or any other year. We need the make/model available to us to make an insatall video. If you are near enough to etrailer, and would like the oppurtunity for a possible free install, please contact the Customer Service number to inquire. But yes, this is an easy install and comes with clear instructions, so no worries about being able to do so yourself. But from one of our top installers, please note the listed steps below.
1. Remove your spare tire
2. Take a strap and run it under your exhaust pipe at the rear axle. I like to hook each side to the spring. Synch the strap up against the exhaust pipe.
3. Spray each of the rubber exhaust hangers in front of and behind the mufflers with soapy water.
4. Use a pry bar, long screw driver, or channel locks to pry each of the rubber hangers off the rods.
5. Slowly lower the exhaust with the strap but do not let it hang free. You just want to lower it enough to give you room to work.
6. On the inside of each frame rail you will find weld nuts. You will be using the two most rear ones on each side. Take one of the bolts in your kit and hand thread it into each one of the weld nuts. If any of them cannot be hand threaded into the weld nut it needs to be cleaned. Spray some lubricant inside and take a tube brush and clean the threads. After cleaning repeat hand threading bolt into weld nut.
7. Take a bolt from your kit, slide on a conical tooth washer, make sure the teeth are facing the hitch, raise the hitch up into position and thread the bolt into on of the weld nuts. Repeat this for each weld nut being used for the hitch.
8. Once all hardware is installed, torque each to the specifications listed in the instructions.
9. Once torqued, spray each of the rubber hangers with soapy water again, raise exhaust back up and slide each of the rubber hangers back onto the rods.
10. Once all hangers are back in place remove the strap.
11. Reinstall your spare tire. You may have to slide the most rear portion of the tire over the hitch cross tube prior to fully securing the tire up to the bottom of the vehicle.
12. Once you have fully installed your spare tire your set.don't currently have a video for installing the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 76268 on the 2020 Acura RDX however, I am an installer here so I can walk you through step by step how to install it.
![Michael R](https://images.etrailer.com/static/images/catg/people/2370_tn.jpg)
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Will Trailer Hitch Get in Way of Kick Sensors for 2020 Acura RDX Advanced Model
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How To See If 2019 Acura RDX Has Plus 12v Power Provision Without Removing Interior Trim Panels
- Q&A: Trailer Hitch Recommendation for 2020 Acura RDX
- Q&A: Weight of 2024 Acura RDX etrailer Hitch Receiver for Installation
- Q&A: Recommended Trailer Hitch for a 2023 Acura RDX
- Q&A: Is Additional Fuse Needed to Install Tekonsha Trailer Wiring in 2019 Acura RDX
- Article: Best Bike Racks for Electric Bikes
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: Which Hitches are Made in the USA
- Article: How to Choose a Hitch-Mounted Bike Rack
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com