Rear Suspension Enhancement that Fits 2001 Workhorse W20 Chassis RV

Question

Question:

I am looking at the air lift springs. They seem to fit the w20 of 2002 but not the w20 of 2001, is this for real? I had always thought that these two were identical. This is for a workhorse chassis of course

asked by: Bruce H

0

Expert Reply:

I checked with Air Lift and they confirmed that the kit only fits the 2002 and newer W20. We do have a Timbren kit part # TGMRP30 that fits your 2001 W20 which would give you the same support but has advantage of not requiring you to monitor air pressure.

expert reply by: Jameson C

0

Answer 1

I do have suspension enhancement options for a 2002 Workhorse P42 Chassis but there are no air bags available unfortunately. Instead, you can use the Timbren Rear Suspension Enhancement System. The correct one will be based off the suspension. The…

view full answer...

Answer 2

Yes, the SumoSprings Custom Helper Springs Kit #SSF-280-47 that you referenced has been confirmed to work with the leaf spring suspension you have on your 2004 W22 Workhorse Holiday Rambler. I attached a picture that I took from the installation…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 7

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 10

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 11

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...

Answer 12

I highly recommend going with the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ over their Ride Control system for your 2023 Toyota Tacoma 4WD because they not only offer more support, but they also have a better construction so they'll…

view full answer...