Overall Length of the Empire Faucets RV Slide Bar Handheld Shower Set

Question

Question:

What is the total length from top to bottom including the mounting hardware? I need one that is 24 inches in in brushed nickel.

asked by: Loren L

1

Helpful Expert Reply:

The Empire Faucets RV Slide Bar Handheld Shower Set, # EM94JR comes in brushed nickel and is overall, 25" from the outside edge of one base on the mounting bracket to the outside edge of the opposite base mounting edge. Please note the linked product review video where, starting at the 2:30 mark, provides a visual of the points measurements are taken.

expert reply by: Michael R

1

Answer 1

I attached a picture that shows the install instructions for the Patrick Distribution RV Slide Bar Hand-Held Shower Set #277-000035 that you referenced. Basically the slide bar attaches to the wall and then there are two silver covers that fit over…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

I do see your Demco Autoslide 5th Wheel Trailer Hitch #DM8550035 is missing the Capture Plate #DM14743-95 and other components on the Head #DM6081. And as you have a Rhino pin box you need the Locking Plate #DM76FR as well to prevent the Demco from…

view full answer...

Answer 8

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 9

The actual puck itself is a standardized size between each brand so the only measurement that matters is the spacing of the pucks, which differs between each vehicle manufacturer. I've attached a diagram below with the spacings used by…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 12

We have replacement legs for the HappiJack truck camper systems like the part #LC736515 which has 36-1/2 inches of lift and a 2,800 lb capacity as well as the #LC736514 which has 34-1/2 inches of lift and a 2,200 lb capacity but the legs themselves…

view full answer...

Overall Length of the Empire Faucets RV Slide Bar Handheld Shower Set

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching