Determining Which Replacement Parts Fit Lippert 8000lb Axle

Question

Question:

Do you source parts for 8K Lippert Axles, axle part #V000415726 ?

asked by: Brad G

0

Expert Reply:

We have exactly what you are looking for.

I reached out to my contact at Lippert and based on the information on the axle tag you provided your 8000lb axle uses the following replacement parts:

Inner bearing: # 25580
Inner race: # 25520
Outer bearing: # 02475
Outer race: # 02420
Grease seal: # GS-2250DL

However we do not sell the hub/rotor assembly that is needed for your axle but it can be order through Lippert as part number 792676.

expert reply by: Samuel C

0

Customer Picture
(click to enlarge)

Answer 1

You can get the longer U-bolts here; I checked with Roadmaster, and the 2630 are simply 7 inch long U-bolts, so you can use the following: - 3" Round Trailer U-Bolts (Qty 2) #SP01-060 These are 7 inches long so they are the same, and for a…

view full answer...

Answer 2

Since you have 8K 3" axles you'll just need the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3" Trailer Axles #RM-2460-2580. The 3-1/2" requirement you were getting with the #RM-2470-2580 was simply…

view full answer...

Answer 3

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 4

The Bearing Kit #BK2-100 should contain all the correct bearing, seals and races for 1 wheel. I always recommend pulling one hub apart and confirming the correct spindle. These fit the most commonly used axles under your 2014 Forest River R-Pod 179…

view full answer...

Answer 5

For your application you need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K to replace the Tru-Ryde RVD-H-545 trailer hub/drum assembly. This is designed for the industry standard #84 spindle so it uses inner bearing…

view full answer...

Answer 6

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 7

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 8

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 9

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 10

If you look at the outermost part of the spindle on your axle there will be what is called a grease zerk or grease gun fitting. It will look like a tiny round ball which is where you can attach a grease gun to grease your spindle. If your spindle has…

view full answer...

Determining Which Replacement Parts Fit Lippert 8000lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching