Dimensions of the Heavy-Duty Crossbar Fit Kit U-Bolts # RUBK

Question

Question:

What are the measurement of the U-bolts? Height and width..Thanks

asked by: Sean

0

Expert Reply:

I spoke to my contact at Rhino Rack to get the dimensions of the U-bolts of the Heavy Duty Crossbar Fit Kit # RUBK and found that it measures 2-3/4 inches from the top of the threaded portion of the U-bolt to the bottom of the u-bolt and measures 2-1/4 inches across measured from the inside.

Check out the picture I attached to see these measurements.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went in the warehouse and measured the U-bolt from Rhino-Rack Heavy-Duty Crossbar Fit Kit , part #RUBK-MF. The width from center to center of the U-bolt is 2-5/8 inches. The height of the U-bolt is 3-5/32 inches. The amount of thread on each bolt…

view full answer...

Answer 2

Yes, you will need the Thule universal change key, #853-1251, to remove and install new lock cores. the change key pulls down all the tumblers so the lock can be removed or inserted. The existing lock, if present, will have to be unlocked for the…

view full answer...

Answer 3

It sounds like you are looking for a replacement U-bolt that measures 4 inches wide. We do carry part #TH09243, that measures 4 inches wide and 2 inches deep. I have included a photo of this U-bolt with the dimensions noted you can check out. This…

view full answer...

Answer 4

The U-bolt part #TH02943 that you referenced is 4 inches wide when measured from center to center of the threaded portion of the u-bolt. Check out the picture I attached that shows this dimension.

view full answer...

Answer 5

The Replacement U-Bolt for the Thule Sidekick, part #TH02943 has the following dimensions: 2 Inches Tall 4 Inches Wide 2 Inch Arms 1 Inch Threaded Arms 3-3/16 between the narrowest point of the arms. I've included a diagram that details…

view full answer...

Answer 6

Yes, the U-Bolts that come with the Replacement Mounting Hardware for Car Top Cargo Roof Cargo Box #CTC-18PARTS have a 3/16" diameter and are spaced 4" apart on center. I have attached some photos to demonstrate this and some other…

view full answer...

Answer 7

I've included an image that details the exact dimensions of the Rola Replacement Bracket, part #59506 The distance between the arms of the top bracket is 4.5 inches, and the distance between the arms of the lower bracket is about 6 inches.

view full answer...

Answer 8

The threaded portion of the u-bolts in the RhinoRack Crossbar Fit Kit, part #S280, measures 1-1/8 inches. This kit consists of 4 u-bolts, 8 plastic knobs with threaded steel inserts, 8 washers, 8 plastic caps for ends of the u-bolts, and 4 metal…

view full answer...

Answer 9

Since the Thule Roof Rack Roller #TH39PF just mounts into the t-slots on the Thule ProBar you'll have no issues fitting it to your Thule TracRac since they have the same t-slot dimensions.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...