Does etrailer LED Tail Light Kit e98943-44LED Include The Mounting Brackets?

Question

Question:

is mounting brackets included in this light kit?

asked by: John B

1

Helpful Expert Reply:

The etrailer License Plate and LED Tail Light Mounting Kit for Hitch Mounted Cargo Carrier # e98943-44LED you were looking at includes everything needed to get this installed on your cargo carrier..

I included a video of the # e98943-44LED being installed for you to take a look at.

expert reply by: Samuel C

1

Answer 1

The Optronics Sealed, Streamline LED Trailer Light #STL79RB referenced in your question will work to provide an additional light on your bike rack, however there may be easier options. You might have trouble mounting the light assembly to the rack…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I checked with the manufacturer, Curt, for you and can verify that yes, the Curt hitch does fit your 2022 Subaru Ascent Onyx Edition: - Curt Trailer Hitch Receiver #C25VR This will give your Ascent a nice option for a hitch that can be concealed, and…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

The best hitch receiver for hauling a bike with your 2022 Subaru Ascent is going to be the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item #C25VR. This hitch receiver mounts behind your rear bumper bar instead of below your…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

The connector you are looking for to install the Curt trailer wiring kit part #C56040 on your 2019 Subaru Ascent is located behind the driver side rear panel in the cargo area. If you check out the picture I attached you'll see where to find it.

view full answer...

Does etrailer LED Tail Light Kit e98943-44LED Include The Mounting Brackets?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching