How To Keep Trailer Battery That Powers Winch Charged While Its Being Towed
Question:
Iv just read this bellow, and I need to do exactly the same. My question is, how do I connect it to the battery in the trailer? Question: I need to charge a marine 12v battery that powers a winch and tongue jack in a 24inch enclosed race car trailer. The tow vehicle is a Toyota Tundra and has 7 pin round connector. I want the trailer battery to charge from the Tundra when the 7 pin is connected. asked by: Joseph F Expert Reply: You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part # 10-1-1 sold by the foot, from this pin to the positive terminal of the battery. You should note that this wont charge a dead battery, but it will keep the battery topped off when you are towing the trailer. expert reply by: Jameson C
asked by: Paul 8
Expert Reply:
I would be happy to help!
If the maintenance charge is enough for your battery, then running the # 10-1-1 from the 12v accessory circuit of your 7-way connector to the positive terminal of your trailer's battery using a ring terminal # DW05705-1.
Keep in mind that this will not keep the battery from draining while using a winch or tongue jack, as this circuit does not offer much power.
To keep the battery from going dead a better option would be running the Bulldog Winch Rear Wiring Kit # BDW20026 from the battery of your tow vehicle to the rear of the truck, and then run the extra wire from the battery on your trailer to the tongue of the trailer. Adding the two included connectors to each set of wires will give you a way to connect and disconnect them when towing the trailer. I also recommend adding a battery isolator like the # DW08771 to keep your vehicles battery from being drained while it is not running.
This will charge your trailer battery from your alternator.
I included a video o the # BDW20026 for you to take a look at.
Products Referenced in This Question
Ring Terminal - 12-10 Gauge Wire - 3/8" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/8 Inch Diameter
- 12-10 Gauge
- Deka
more information >
Deka Battery Isolator - 120 Amp
- Battery Charger
- Battery Isolators
- 6V
- 12V
- 24V
- 36V
- 48V
- 50V
- Vehicle Battery to Auxiliary Battery
- Deka
more information >
Product Page this Question was Asked From
Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 3 Gauge - 24' Long
- Accessories and Parts
- Electric Winch
- Wiring
- Wiring Kits
- 24 Feet Long
- 3 Gauge Wire
- Bulldog Winch
more information >
Continue Researching
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)
- Article: Trailer Wiring Diagrams
- Q&A: How to Charge a Trailer Battery Through a 7-Way Connector
- Shop: Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 3 Gauge - 24' Long
- Shop: Deka Battery Isolator - 120 Amp
- Video: CTS Trailer Breakaway Kit - Kit Only - HBA-EBA Review
- Video: Stromberg Carlson Trailer Jack LG-217884 Review
- Video: Review of Lippert Standard 5th-Wheel Power Landing Gear Motor, Switch, and Harness - LC217884
- Video: Review of Bright Way Trailer Breakaway Kit - Kit with Charger - 3802311
- Video: Lippert Components Trailer Jack LC142178 Review
- Video: Review of Curt Trailer Breakaway Kit - Kit with Charger - C52044
- Shop: Lippert Venture 5th Wheel RV Landing Gear Motor
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Shop: Lippert Standard 5th-Wheel Landing Gear Motor w/ IP Rated Switch and Harness
- Search Results: lippert
- Search Results: trailer battery charger
- Search Results: landing gear motor
- Search Results: battery kit
- Search Results: battery charger
- Q&A: Is a Battery Isolator Needed When Using 7-Way Connector To Charge the Trailer Battery
- Shop: Trailer Hitch
- Shop: Erickson E Track Tie Down Ring - 1,333 lbs
- Shop: Erickson Strap Hanger and Storage Unit - 6" Wide
- Q&A: Troubleshooting Bulldog Electric Trailer Jack with Dead Battery
- Q&A: Could Brophy D-Ring Tie Down Anchor # SR15-C Attach to Wood Floor
- Q&A: Is 3/4 Inch Plywood Floor Adequate for D-Ring Tie Down Anchors with Backing Plate for 3,000 lb Car
- Q&A: Installation Methods for Brophy Recessed Trailer D-Ring Tie Down with Backing Plate # RR5K
- Q&A: Wiring Harness Needed To Install Replacement Motor for Stromberg Carlson Electric Landing Gear
- Video: Race Ramps Trailer Loading Assist Ramps Review
- Shop: Towing Mirrors