Roof Rack Recommendation for 2018 Audi Q5 for Attaching Thule Hullavator

Question

Question:

I have an audi q5 2018. What thule croosbar is recommended for my car in case I decide to also get a Thule hullavator pro? And do the croosbars need the thule podiums foot if I decide to latter install the thule elevator pro?

asked by: Ennio C

0

Expert Reply:

The Thule Wingbar Evo roof rack for your 2018 Audi Q5 part numbers # TH711320, # TH710601, and # TH186045 would be the best for attaching the Thule Hullavator # TH898 to. The Hullavator would easily fit into the top channels of the Wingbars for a clean and solid connection.

expert reply by: Jameson C

0

Answer 1

The Thule Hullavator load-assisted kayak carrier #TH898 will directly mount onto just about any roof rack bar shapes, including round, square, aero, elliptical, most factory crossbars, and most crossbars with top "T-slot" channels. Yakima…

view full answer...

Answer 2

The Thule Hullavator Pro - Lift Assist Kayak Carrier #TH898 requires a minimum of 4" overhang on both sides, no matter which crossbar setup you go with. For your 2019 Subaru Forester I recommend going with the Malone Airflow2 aero crossbars. Not…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The Thule Hullavator Pro, part #TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those…

view full answer...

Answer 7

There is not a general restriction from Thule that says two Hullavator Kayak Carriers #TH898 can't be used on a Thule roof rack. As long as the crossbars on your Ford Escape have the required length for two sets and a sufficient weight capacity…

view full answer...

Answer 8

The brackets on the Thule Hullavator 897 and the Thule Hullavator 897XT are not the same. The first generation Hullavator was designed to only work with Thule square bars, so it will not work with your Thule WingBar Evo. The updated model, 897XT, was…

view full answer...

Answer 9

For your 2018 Honda HR-V to be compatible with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898, you have to use slightly longer crossbars. The Hullavator requires 4-8 inches overhang to give clearance. In order to give…

view full answer...

Answer 10

Yes, you will be able to use the Thule Hullavator Pro Kayak Roof Rack #TH898 with the Rhino-Rack Vortex Aero roof rack having 59" crossbars. You will need the Crossbars #RRVA150B-2, Legs #RRRLKVA and Fit Kit #DK079 to complete the rack on your…

view full answer...

Answer 11

There are two ways to connect the Thule Hullavator to your crossbars, clamp on or use the T-slot. Clamp on requires square bars and T-Track requires a Thule Crossbar. If you have raised side rails on your vehicle, the SteelTop #MPG203 will just clamp…

view full answer...

Answer 12

Hello Paul thanks for your question. When installing the Thule Hullavator Pro #TH898 it is completely normal to have 4 leftover bolts. The length of the bolt you use is determined by what kind of crossbar you are using. The 35mm bolts are intended…

view full answer...