Who Manufactures AKEBRK-7L-SA 12-Inch Self-Adjusting Trailer Brake Assemblies

Question

Question:

Please advise the company making this item

asked by: Bruce B

0

Expert Reply:

The etrailer brand brake assembles such as the # AKEBRK-7L-SA 12 inch self-adjusting trailer drum brake assembly are manufactured by AxleTech. We offer them as a less-expensive alternative to the Dexter # 23-458.

expert reply by: Mike L

0

Answer 1

The correct bearing kit for your 7,000 pound Lippert axle is #BK3-210.

view full answer...

Answer 2

The Lippert 7,000 lb axles use a seal that is 2.250 inches inner diameter and 3.376 inches outer diameter. You will want Grease Seals 10-36 (pair) #RG06-070 for the replacements or complete bearing kit #BK3-200 which includes replacement bearings,…

view full answer...

Answer 3

Tire balancing at many tire shops is done quickly and accurately with vehicle tires using a balancing machine that allows the operator to use the center hub for balancing. It centers the wheel by the hub and spins the tire allowing them to see where…

view full answer...

Answer 4

Self adjusting brake assemblies have no downside. They are the preferred brake assembly style as they require no adjustments. The part #AKEBRK-7L-SA is the correct left hand side assembly for your trailer with 7k Lippert axles. For the right hand…

view full answer...

Answer 5

If you currently have 12" self-adjusting brakes for a Lippert 5,200lb-7,000lb axle, then the etrailer.com self-adjusting brake assemblies for the right hand side #AKEBRK-7R-SA and left hand side #AKEBRK-7L-SA are the direct replacements. If your…

view full answer...

Answer 6

When installing electric trailer brakes you will only need to run wire from the brake output circuit of your trailer connector to the brake assemblies. You will not need to install any other electric devices to complete the wiring. You will also need…

view full answer...

Answer 7

Based on the description you have provided (thank you) the Dexter Nev-R-Adjust brake set, #23-458-459, will indeed be a fit! Another option that will save you some money is the etrailer brake set #AKEBRK-7-SA. These are also automatically adjusting…

view full answer...

Answer 8

Yes, chrome #12CLN and stainless steel #CE11051 are the 1/2" lugnut finish options for the #274-000023. My recommendation would be to either match as closely with the chrome lugnuts or consider a cover like the Phoenix USA QuickTrim Hub Cover…

view full answer...

Answer 9

The difference between the two is just the brand basically as they are both the left hand side brake assemblies for a 7,000 lb axles and are self adjusting. The #23-464 is the Dexter brand and #AKEBRK-7L-SA is our etrailer brand.

view full answer...

Answer 10

We do carry the exact brakes that you need for your B12E-02 AxleTek 12-GG Axle. For the Left Assembly you will want part #AKEBRK-7L-SA and for the Right Hand assembly you will want part #AKEBRK-7R-SA. These brake assemblies are made by AxleTek and…

view full answer...

Answer 11

30-50 ft lbs of torque is the recommended torque spec for installing the etrailer.com brake assemblies part #AKEBRK-7L-SA. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty…

view full answer...

Answer 12

I would recommend checking 2 adjustments on your brake setup to make sure they are adjusted correctly. The first adjustment is on the back of your drum brakes using a special pry tool, like the #W80630. You will want to turn the adjustment gear…

view full answer...

Who Manufactures AKEBRK-7L-SA 12-Inch Self-Adjusting Trailer Brake Assemblies

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching