Could Replacement New-Style Linc Remote Work for 2014 Forest River Wildcat Maxx

Question

Question:

I have a 2014 forest river wildcat Maxx travel trailer. I lost my touchscreen remote and would like to replace it with the # lc292614 style remote. Will this remote work with my trailer?

asked by: Steve M

0

Expert Reply:

If you have the Linc system in your 2014 Forest River Wildcat Maxx travel trailer the part # LC292614 would work for you. But if you have a different setup you'd need to look at something else.

expert reply by: Jameson C

0

Answer 1

The momentary push button is actually not on the remote part #LC292614 that you referenced. It's on the receiver of the LINC system. I reread the instructions a few times till I caught that too so I understand the confusion! Normally the…

view full answer...

Answer 2

Based on your description it sounds like you have the Replacement New-Style Linc Analog Remote - 5 Function #LC292614. In order to sync this remote you need to start by pressing and holding the momentary push button on the receiver. Next, press the…

view full answer...

Answer 3

The three bottom LEDs blinking means that the remove #LC292614 is waiting to be programmed. When it's in this state you will use the "IN" and "OUT" buttons to cycle through the LED descriptions until you get to FUNCTION 1.…

view full answer...

Answer 4

We get this question a lot. The momentary push button on your Lippert LINC system that you need to press to program the Remote Control #LC292614 is not on the remote, but rather on the LINC receiver box which is usually located near the generator.…

view full answer...

Answer 5

In order to sync the Linc Analog Remote part #LC292614 you will want to follow the steps I have listed for you below: 1) Press and hold the momentary push button on the receiver. 2) Press “Light” (A) button on the transmitter until relay on receiver…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Could Replacement New-Style Linc Remote Work for 2014 Forest River Wildcat Maxx

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching