Will the Longview Custom Towing Mirrors for a 2019 Ram 1500 Work With Turn Signals and Spot Lights

Question

Question:

I assume these will fit my 2019 Bighorn Ram Quad cab. This pair have the plastic clip and thumb screw? Also I have the turn signal,and bottom flood light....

asked by: Nick C

1

Helpful Expert Reply:

Yes, the Longview Custom Towing Mirrors part # LO34FR are a fit for a 2019 Ram 1500 (All Models) with turn signals and flood lights integrated into the mirrors. There are cutouts in the towing mirrors to allows these features to be retained.

expert reply by: Conner L

1

Answer 1

The K-Source Snap & Zap Custom Towing Mirrors #KS80730 are our best towing mirrors for your 2023 Ram 1500. These are custom fit and require no additional hardware to install them on your mirrors. They also have cutouts for integrated turn…

view full answer...

Answer 2

The Longview mirror #LO34FR that you referenced is flat on both sides. Neither mirror has a convex surface like you are not wanting.

view full answer...

Answer 3

It's pretty rare actually that we get customers asking for replacement hardware for the tow mirrors we carry. I wouldn't anticipate yours wearing out. 

view full answer...

Answer 4

For your 2021 Ram 1500 there are three tow mirror options available that were custom fit for your truck. There's the K-Source part #KS80730, the CIPA #CIP98MR, and the Longview part #LO34FR all of these are going to fit well but for you I…

view full answer...

Answer 5

There has been no update to the design of the K-Source Snap & Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side #KS80730. I was unable to find any reports of these mirrors scratching the factory paint, but I did find quite a few…

view full answer...

Answer 6

I have a great set of towing mirrors for your 2022 Ram 1500. I recommend the Longview Custom Towing Mirrors item #LO34FR. These are a slip on style attachment for both your driver and passenger side. The Longview Slip On Towing Mirror will extend the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Will the Longview Custom Towing Mirrors for a 2019 Ram 1500 Work With Turn Signals and Spot Lights

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching