Availability of Bearings 1779 and 2788

Question

Question:

I am looking for replacement for bower 1729x race,1779 bearing,2729 race,2789 bearing.and the grease seal for tandem trailer.can you assist

asked by: Wayne T

0

Expert Reply:

We have the bearing part # 1779 and the race part # 1729. We also have the race part # 2729 and the bearing # 2788.

Since I am not able to determine what seal you need based on your numbers I'd need you to get me the diameter of the spindle where the seal rides as well as the diameter of the hub where the seal installs.

expert reply by: Jameson C

0

Answer 1

The bearing numbers you have provided indicate that you have hub 22834. This hub is no longer made but there are parts for it such as the bearings #2788 and #1779 an the races #2729 and #1729. The hub is rated for 2,600 pounds which means it fits a…

view full answer...

Answer 2

We do have the bearings, races, and a grease seal that seems to match. For the bearings and races you just need to enter the numbers you have given me and they will come up but they are not available in a kit. #1779 (outer bearing) #1729 (race for…

view full answer...

Answer 3

So after quite a bit of research it seems that the Trostel 300-156-6 seals you mentioned are quite old and have not been around for some time. The best I could find was that they are 3.00" in outer diameter, and I did manage to find a…

view full answer...

Answer 4

We do offer the #1779 bearing which has a .938 inner diameter, as well as the compatible race as part #1729. It's our house brand manufactured for us by TruRyde. We don't offer a 2780 bearing, which has a 1.4365 inner diameter.

view full answer...

Answer 5

Bearing #2788 has an inner diameter of 1.50-inches and fits race #2729. Bearing #1779 has an inner diameter of 0.938-inches and fits race #1729. We do offer all of these bearing and race parts and if you wish you can install new bearings in your…

view full answer...

Answer 6

More than likely, no. Any given spindle and hub will take specific bearing sizes. A bearing that is too large will not fit inside the hub or on the spindle. Bearings that are too small for the hub will create a very dangerous situation. I would need…

view full answer...

Answer 7

We have a large selection of 12 x 2 electric brake assemblies available, which I have linked for you to look through. I recommend looking at the etrailer.com Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-7-SA. These 12 inch assemblies are…

view full answer...

Answer 8

I was unable to find any reference to a Hadco 3107, but I can tell you how to determine the correct replacement hub. There's a number of different things you'll need to know; first, you need to know the weight rating of your axle, and also…

view full answer...

Answer 9

Most likely the colors would match with the exception of the red wire on the trailer going to the white wire on the truck. The white wire is the ground circuit so you can trace the RED wire on the TRAILER to see if it attaches to a metal surface on…

view full answer...

Answer 10

Normally, the green wire on the right side carries right turn signal and brake light functions and the brown wire carries running light functions. On the left side, the yellow wire carries left turn and brake lights and the brown wire again carries…

view full answer...

Answer 11

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Availability of Bearings 1779 and 2788

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching