Is There a 12 Volt Male End Wire For MaxxFan Dome MA00-03812B

Question

Question:

Hi, I would like to run this fan off of the 12v plug on our Jackery 500 in our Tear camper. The vent will be in the ceiling and I want to run the wire down to the Jackery. I was wondering if you sold a wire with a 12v male end that I could hook to the wire on the vent. Do you also sell an electrical box with a flat cover so I can connect the wire in the box? That way if the vent dies I can just unhook the wiring in the box, and install a new fan. Im picturing the wire from the vent going into an electrical box, and connecting to either the wire with the 12v male end, or an intermediate wire that would go between the vent and the 12v male end. The ceiling thickness is about an 1.5inch so its too shallow for a standard electrical box. Thanks in advance

asked by: Jon B

0

Expert Reply:

There is not a 12 volt wire with a male end or an electrical box with a flat cover available to wire in the MaxxFan Dome Roof Vent w/ 12V Fan - 6" Diameter - Manual Lift - Black # MA00-03812B.

The only other parts we offer for the install of this vent is the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White # 344270KITW.

expert reply by: Kyle S

0

Answer 1

We do offer a vent fan which can be mounted on the side of a wall, the MaxxFan Dome Roof Vent part #MA00-03812B for black or part #MA00-03812W for for white.

view full answer...

Answer 2

The MaxxFan Dome Roof Vent part #MA00-03812W will work just fine on passenger vehicle with thin metal roof as many others have done so as well. That said, you will need to add some material like plywood between the roof and fan to get the required…

view full answer...

Answer 3

Yes, if you'd like you would be able to mount the MaxxFan Dome roof vent on its side. I have added a photo that a customer sent in showing the same vent (in black) mounted on its side; the vent is designed to fit roofs (or walls) that are between…

view full answer...

Answer 4

You could technically install the MaxxFan Deluxe Roof Vent #MA00-07500K in the roof of your mini van.That being said, the main issue is going to be the mini van's roof thickness. Since the roofs on vehicles are significantly thinner than those…

view full answer...

Answer 5

In regards to the RV Tub Drain with Threaded Stopper part #372184030-A, the hole size that the drain is designed to fit is 2" whereas the fitting size that attaches to the drain pipe is 1-1/2".

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Is There a 12 Volt Male End Wire For MaxxFan Dome MA00-03812B

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching