Best Trailer Wiring Harness for 2017 Mitsubishi Lancer
Question:
whats the best/easiest wiring harness to use for this trailer hitch?
asked by: Hunter
Expert Reply:
All the trailer wiring harnesses we offer for the 2017 Mitsubishi Lancer would install in the same manner.
The harnesses would all connect inline at the connection of the vehicle's taillight harness and the taillight assemblies. You'd then need to run a wire under the vehicle to the positive battery terminal to power the trailer lights. I'd recommend the Tekonsha # 118538, as I've found over the years that their taillight converter/trailer wiring harnesses work the best with the fewest problems compared to the others that are available.
You'll also need a ball mount like # C45521, a hitch pin like # PC2 and a trailer ball like # 19256 for a 1-7/8 or
# 19258 for a 2 inch ball.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Q&A: Recommended Trailer Hitch And Trailer Wiring For 2013 Mitsubishi Lancer Hatchback
- Q&A: Difference Between The Curt & etrailer Class III 2 Hitch Receiver
- Q&A: Is Weight Capacity of Yakima CoreBar Crossbars Per Bar or for Pair
- Article: How to Use a Roof Rack (Like a Boss)