Replacement Step Motor for Kwikee Steps with Motor 369545

Question

Question:

Is the same motor used for the single step and double step? My motor has the number 369545 on the tag.

asked by: Frank J

0

Expert Reply:

The correct replacement for a Kwikee Step Motor 369545 is the Replacement Motor for Kwikee Electric RV Steps part # LC379147. I was able to confirm this with Lippert for you.

expert reply by: Erik B

0

Answer 1

The correct replacement for a Kwikee Step Motor 369545 is the Replacement Motor for Kwikee Electric RV Steps part #LC379147.

view full answer...

Answer 2

The LC369545 is what the manufacturer labels both the motor and gear box together but for just the gear box you'd want the part #LC379161 that you referenced.

view full answer...

Answer 3

We do have a pressure relief valve for your Furrion RV Tankless Water Heater #FR93FR. The Camco RV Water Heater Temperature and Pressure Release Valve #CAM10423, is a 1/2 valve with a 4" probe that will help protect your RV's water heater…

view full answer...

Answer 4

I checked with Kwikee and the correct replacement motor you need for your setup that has the LCI part number 369545 is the part #LC379147.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 8

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement Step Motor for Kwikee Steps with Motor 369545

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching