Fifth Wheel Rail Kit that Fits 2021 Ford F-150

Question

Question:

Looking for Reese rail and mounts for 2021 Ford F-150. I already have the gooseneck ball plate.

asked by: Kevin T

0

Expert Reply:

For a fifth wheel rail kit that fits your 2021 Ford F-150 we have the Reese fifth wheel rail kit part # RP50087-58 which is a confirmed fit for your truck and would work great with your fifth wheel to gooseneck hitch adapter.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

Yes when installing the universal rail kit part #RP30035-31 you'd want to install the rear rail edge 28-3/4 inches from the rear of the truck bed edge.

view full answer...

Answer 3

Yes, the Adapter Rail for Curt 5th Wheel Hitch's part #C88KR which is a fit for a 2021 Chevrolet Silverado 3500 will work with a Reese 16K 5th Wheel Hitch. They are simply above bed rails so they will work with Curt, Reese, Husky etc. hitches.

view full answer...

Answer 4

Based on our experiences here I would recommend the Reese 16k hitch part #RP30047 over the Curt hitch part #C16120 that you referenced. The Reese hitch seems to be a bit more reliable and the Curt Q series comes back more often with damage around the…

view full answer...

Answer 5

The reason the Reese fifth wheel rail kit part #RP50087-58 is interfering with your sensor is because it doesn't fit the 2021 models of the truck. Reese made a new rail kit for your truck with the part #RP56034-53 which would be what you'd…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Fifth Wheel Rail Kit that Fits 2021 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching