Installation of Air Lift 1000 Air Helper Springs # AL60815 on 2012 Honda Odyssey

Question

Question:

Do the coil springs have to be loosened to get bags inside or is it possible or practical to squeeze them in .OR can I get some installation data before I purchase?

asked by: Bob B

0

Expert Reply:

To install the Air Lift 1000 Air Helper Springs, part # AL60815, on your 2012 Honda Odyssey, it does require the coil springs to be removed from the vehicle. The rubber jounce bumper that is inside the coil spring will have to be unbolted and removed. Then, the air spring will be installed into the coil spring and the whole coil spring with air spring will be installed back on the vehicle. A hole will need to be drilled in the control arm of the vehicle for the stem of the air spring to fit into.

I am including a link to the installation instructions on the Air Lift helper springs.

expert reply by: Jeff D

0

Answer 1

There is big misunderstanding on how the air springs which fit inside coil springs like the Air Lit #AL60815 for your 2012 Honda Odyssey work. Many think the air spring inflates vertically like a traditional air spring but on these they actually…

view full answer...

Answer 2

I spoke with my contact at Air Lift and he said if you do not intend to tow or haul a trailer, using AirLift 1000 Air Helper Springs for Coil Springs #AL60815, which you reference, on your 2015 Honda Odyssey will actually make for a stiffer ride.…

view full answer...

Answer 3

The trick is to always have a couple pounds in the air bags at all times. If you do this the air bags of the Air Lift AirLift 1000 #AL60815 should last the life of your vehicle. This product also has a lifetime warranty. I attached installation…

view full answer...

Answer 4

Hey Emanuel, so I have a video attached to this page that will show you the process but it's not of the exact kit part #AL98WQ that you asked about. The process is basically identical though as it's basically just about getting the air bag…

view full answer...

Answer 5

The 205/65-10 trailer tire size comes in different load ranges and each load range has a different psi requirement. A load range B in this size should be inflated to 35 psi. Load range C inflate to 50 psi. For load range D inflate to 70 psi. And for…

view full answer...

Answer 6

There is one option for suspension enhancement for your 2019 Honda Odyssey, though there are no SumoSprings that fit. Instead, the enhancement that does fit is the Timbren Rear Suspension Enhancement System #T26FR. The Timbren jounce springs will…

view full answer...

Answer 7

The primary difference is a matter of numbers. When installed, the Draw-Tite Class III #76025 will sit so the inside top edge of the receiver tube sits about 13 inches above the ground, and the receiver tube will sit under the bumper so that the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

For your 2017 Honda Odyssey the only suspension enhancement option we have is the Timbren Kit part #THROD2 that you referenced. I attached a diagram that covers how it installs but at this time we do not have an install video.

view full answer...

Answer 10

Yes you will need to trim away the factory bump stops to install Air Lift helper springs #AL60728 on your 1997 Lexus LX 450. The installation will be similar to the Firestone kit #F4124 so I have linked its instructions since there aren't any…

view full answer...

Installation of Air Lift 1000 Air Helper Springs # AL60815 on 2012 Honda Odyssey

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching