Location of Wiring Connections to Install Pop & Lock PL8662 Tailgate Lock on 2013 Honda Ridgeline

Question

Question:

Hi. I am looking into a BAKFlip tonneau in the future. Buut first I plan to instal a tailgate PopandLock. I would like to know how and where the electrical connection is for the power lock so I can decide if I want a power lock or just manual. Is there a manual that shows that instalation? I see a PopandLock video. Item I am looking at is. PL85513 Thanks

asked by: Phil M

0

Expert Reply:

The # PL85513 you'd looked at is for a 2005-2015 Toyota Tacoma, and won't work with your Ridgeline, you'll want to use # PL8662 which is compatible with Ridgeline models with or without the factory back up camera..

The wiring connection used to tie in the Pop & Lock # PL8662 into the wiring of your Ridgeline is located behind the driver's side kick panel that's next to your left ankle when you're sitting in the driver's seat. Remove the kick panel and locate the fuse box. The 'lock' wire is yellow with a black stripe and 'unlock' wire is yellow with a green stripe. The wires are located in the small green plug at the bottom front side of the fuse box.

I've linked to the installation instructions for you.

expert reply by: Mike L

0

Answer 1

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 2

The correct Pop and Lock tailgate lock for your 2013 Toyota Tacoma with a backup camera is the part #PAL5400 which comes with a lock cylinder that will allow you to key to your truck's key. I attached an install video for this for you to check…

view full answer...

Answer 3

The closest option we have to what you are looking for is the part #PL8675 which is intended as a manual and a power lock for your 2019 Honda Ridgeline. If your vehicle didn't have power locks this kit could be used as just a manual lock so if…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 6

That is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit #AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Location of Wiring Connections to Install Pop & Lock PL8662 Tailgate Lock on 2013 Honda Ridgeline

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching