Replacement Antenna for Voyager Back Up Observation System

Question

Question:

We are looking for replacement antennas for our Voyager back up system. Antenna numbers are 3dBi and 5dBi. Both antennas are 90 degree bends. Model number on our cameras are WVCMSQ1B we have 4 and Model number on the monitor is WVOS7MDCL1Q. Do you have anything that will work for us?

asked by: Wendy S

0

Expert Reply:

For replacement antennas the part # VO54FR would work for both positions you mentioned.

expert reply by: Jameson C

0

Answer 1

The rectangular plug at the end of The Replacement 12-Volt DC Power Cord for Voyager LCD Monitor #PXXWVOM541HAR can not be purchased alone. You will have to purchase the whole replacement cord to get the plug, but if the plug went bad on your current…

view full answer...

Answer 2

Since you have a Voyager WiSight camera system the correct replacement antenna is the part #VO54FR and not the one that you mentioned. This has 90 degree angle capabilities as well.

view full answer...

Answer 3

The correct replacement antenna for your WVOM43 system is the Replacement Wireless Antenna for Voyager Backup Camera System #PXXHD0006301R.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Antenna for Voyager Back Up Observation System

Product Page this Question was Asked From

Continue Researching