Is There a King Pin Lock for a Pin Box with Capture Plate/Wedge Installed

Question

Question:

Will this lock work with a capture plate that is used with a Pullright Super glide hitch?

asked by: Michael L

0

Expert Reply:

The best option we have for a king pin lock that will work on a pin box with a capture plate/wedge installed is the AMPLock King Pin Lock for PullRite and Sidewinder 5th Wheel Pin Boxes part # AMP87FR. I have attached a video I did below.

expert reply by: Conner L

0

Answer 1

Yes, the SumoSprings Rebel Custom Helper Springs #SSR-203-47-2 will fit the 2024 GMC Sierra 3500 your customer has.

view full answer...

Answer 2

The service plan for the Galeo Pro part #GA94FR is offered in three time frames currently: Monthly/yearly/3-year service available from Galeo at $1.99/$19.99/$49.99.

view full answer...

Answer 3

The Galeo Pro GPS Tracking Device #GA94FR will need the tracking service plan to tell you where the vehicle is. The service plan is what allows the device to communicate over cell service its exact position.

view full answer...

Answer 4

You're experiencing the harsher ride because the overload springs engage when you tow, so what you're really needing to do is add some support to either prevent or delay the overload springs from engaging. I spoke at length with my…

view full answer...

Answer 5

Measuring on the ground to the inside point of contact of each tire is correct. The Fastway ONEstep Wheel Chocks #FA84-00-4840 would be the right part for you, if your measured wheel spacing is between 16 and 24 inches on your dual-axle trailer.…

view full answer...

Answer 6

The most durable and theft-proof lock I've tested is the AMPLock King Pin Lock for 5th Wheel Trailers part #AMP77FR. The lock itself is very thick, around 10 lbs and it's made of cast iron. It also has a unique key system which prevents…

view full answer...

Answer 7

The AMPLock King Pin Lock for 5th Wheel Trailers #AMP77FR you mention is for deterring theft, while the Demco Autoslide Locking Plate for MOR/ryde Pin Boxes #DM6025 is designed to prevent your king pin from pivoting inside your hitch. The two would…

view full answer...

Answer 8

In order to secure a fifth wheel trailer you can use the Blaylock EZ Lock King Pin Lock for 5th Wheel Trailers part #BLTL-70-40D which attaches to the bottom of the kingpin and would then prevent anyone from being able to couple the trailer without…

view full answer...

Answer 9

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 10

Hey David, for your 1990 Jeep Wrangler the Roadmaster Diode Kit part #RM-15267 would be a really great option. This installs diodes on the Wrangler's taillight circuits which allows the RV to control them. It also comes with the wiring that runs…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Is There a King Pin Lock for a Pin Box with Capture Plate/Wedge Installed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching