Will B and Headache Rack BWPUCP7522BA fit 2018 Ram with Chest Tool Box

Question

Question:

I have a 2018 RAM 3500 crew cab w/8ft bed. I also have a DZ8560WB truck bed utility chest. It looks like installing the will not be an issue with my truck. 1. Will the clearance for the Slat-style , or the narrowing of the headache rack frame, on the bedside interfere with the opening of my utility chest lid? 2. The specs show a height of 26. Is that the height of the cross bar, or is it the height of the Raised tabs at both ends?

asked by: Brad E

0

Expert Reply:

The portion of the mounting bracket of the B&W Custom Headache Rack # BWPUCP7522BA that would install to the inside of the bed rails would not interfere with your tool box. Also, the 26 inch height is the height of the tabs.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You would have no problem setting your crossover style tool box on top of the rails of the B&W Custom Headache Rack #BWPUCP7522BA that you referenced. To allow the box to open though you'll need to move it towards the rear of the truck bed so…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

For the Edge CS2 Evolution Diesel Tuner you will need to enter the programming menu. You will turn on your vehicle without starting it. Then use the Menu button to open the main menu and scroll down with the arrow to the Programming on the screen.…

view full answer...

Answer 4

The Air Lift Air Helper Spring Cradles #AL59DQ are not going to be compatible with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL57589 on your 2021 Ram 2500. This is due to the 7500 springs being larger in diameter than the 5000…

view full answer...

Answer 5

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 6

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…

view full answer...

Answer 7

Yes, I attached a picture to this page that shows what the Westin HDX Grille Guard #57-3550 looks like installed on a similar 2019 Ram 2500.

view full answer...

Answer 8

The Edge Diesel Evolution CTS3 Performance Tuner - 5" Color Touch Screen #EP36YR that you mentioned is confirmed to fit your 2005 Ram 2500 as long as it has the 5.9 diesel. Since the one you are looking at is used, you will want to make sure…

view full answer...

Answer 9

The integrated cable locks that come on the Kuat NV 2.0 Base #BA22B automatically lock when you connect the 2 ends together. When you put the key in and turn it you are actually unlocking it which is why they pop out. If you skip to the 4:15 mark on…

view full answer...

Answer 10

You will naturally see some voltage drop from the brake controller all the way back to your trailer brakes, but what you're describing sounds like a bad ground somewhere. What you need to do is check the grounds related to the trailer brakes and…

view full answer...

Answer 11

The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621 HD - Auto Latch - 25K #GY66FR you were looking at is a confirmed replacement for your Lippert 1621 HD pin box and will not require any shims. The #GY66FR has the same…

view full answer...

Will B and Headache Rack BWPUCP7522BA fit 2018 Ram with Chest Tool Box

Product Page this Question was Asked From

Continue Researching