Difference Between Equal-i-zer Replacement Socket Pin 90-03-9212 and EQ95-01-9400

Question

Question:

What is the length and diameter? How does it compare to part #95-01-9400?

asked by: Phillip T

0

Expert Reply:

The pin length of the # 90-03-9212 is 2-5/16 inches and the diameter is 3/8 of an inch. The only difference between this part and # EQ95-01-9400 is that the # EQ95-01-9400 includes the retaining clip, while the # 90-03-9212 does not. I'd recommend going with the # EQ95-01-9400. Even if you don't need the clip right this minute, they are easily misplaced and it never hurts to have a spare.

expert reply by: Mike L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 8

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...

Answer 11

The brake controller port on a 2021 Ford F-150 (if equipped) will be located behind the coin tray in the center console. This will be accessed by removing the panel under the steering wheel. I have attached a video which shows this below. For a brake…

view full answer...

Answer 12

It does appear you are going to be able to flip the axles on your 2023 Northern Spirit 2145RBX using 2 of the Dexter Trailer Springs Over-Under Conversion Kits #K71-384-00. I will warn you Kalvin this will raise the height of your camper roughly…

view full answer...