Adding Third Panel For Go Power Solar Flex Charging System

Question

Question:

Go Power Solar Flex Charging System with Digital Solar Controller - 220 Watt Solar Panels Item # 34272628. Can the controller in the kit accommodate a third 110 watt flexible solar panel?

asked by: Janet P

0

Expert Reply:

Yes, you can add an additional flexible 110 watt panel to your system. While the 30 amp controller of the Go Power Flex kit part # 34272628 can only accommodate one power and ground cable, the solar panels themselves can connect to each other on top of the RV to then supply the power of multiple panels on that one set of power cables.

expert reply by: Aaron A

0

Answer 1

Your current Zamp connector is only for Zamp branded solar systems. The Go Power Overlander Solar Charging System with Digital Solar Controller - 200 Watt Solar Panel Item #34282181 comes with a 30 amp solar controller that you will need to install…

view full answer...

Answer 2

I'll start by saying that when your camper is pre-wired for use with a Go Power Solar, all of the hard wiring is done for you; all you'll need to do is connect your Go Power Solar panels to the installed cable entry plate and the solar panels…

view full answer...

Answer 3

Choosing the correct solar panel kit can be a bit overwhelming because there are so many options out there. For your application I would definitely get another battery (Lithium are the best) and then you might want to go with the Elite #34282184 over…

view full answer...

Answer 4

Yes the Go Power Overlander Solar Charging System with Digital Solar Controller #34282181 would be a really great choice to charge the 12 volt battery of your 2020 Forest River RP195. Since your Forest River is pre-wired it would have wiring ran to…

view full answer...

Answer 5

I checked with Go Power, and the recommended size of the battery bank to use with the Go Power Solar Elite Charging System - 380 Watt Solar Panels - 2,000 Watt Inverter Charger #34282184 is four batteries, as you can see by the accompanying cut out I…

view full answer...

Answer 6

Thanks for the photo of your SolidStep Manual Fold-Down Steps for 30" to 36" Wide RV Door Frames - Quad - Aluminum #LC791575 with the threshold. You can see in the attached videos if the threshold were larger you would simply attach to it…

view full answer...

Answer 7

The MORryde StepAbove RV Steps, like part #MR26RR, do require that 3/8" gap from the bottom of the door to the top of your threshold but that clearance is reduced to a range of 1/4" to 3/8" for the Lippert SolidStep, like part…

view full answer...

Answer 8

Hey Don; good question and no other parts - including any type of adapter plate or mounting plate - is needed to mount the 30 Amp Go Power PWM Solar Charge Controller with Bluetooth #GP76QR. The #GP76QR comes with screws and is ready to be mounted…

view full answer...

Answer 9

Hi Donald, Yes, a higher amperage charger, like the #GP76QR (30 amp), would be able to provide a faster recharge for your battery bank than a 10 amp controller like the #34280503. When adding in the second battery you'll want to wire it in…

view full answer...

Answer 10

Yes you'd easily be safe to add another Go Power Overlander Expansion Kit #34282182 to your GoPower setup that has a 30 amp controller. You'd be close to the max amperage but you'd be under the 30 amps pretty easily even if they were at…

view full answer...

Answer 11

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Answer 12

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Adding Third Panel For Go Power Solar Flex Charging System

Featured Help Information

Miscellaneous Media

Continue Researching