Hitch Pin Lock For A 2019 Toyota Tundra

Question

Question:

Hi, I have a Hitch Pin Lock that fits on a 2008 Toyota 4Runner, but it is too short to fit on my 2019 Toyota Tundra. Can you recommend which Hitch Pin Lock will fit on a 2019 Toyota Tundra? The receiver is stock and I believe it is double wallinch but I am not sure. Thanks

asked by: Brian D

0

Expert Reply:

I recommend the etrailer Hitch Receiver Lock for 2" and 2-1/2" Hitches - Flush - 3-5/8" Span - Chrome
Item # e98881 for your 2019 Toyota Tundra.

expert reply by: Shane H

0

Answer 1

It sounds like you are looking for a replacement locking hitch pin since you said the lock pin of your hitch. For a locking hitch pin I would recommend the Bulldog Trailer Hitch Lock part #BD580402 as it is stainless steel which is rustproof.

view full answer...

Answer 2

Hitch classifications are a general way to organize capacities but they don't reflect exact weight ratings. So while the Class V can be on somewhat higher and lower weight capacities but typically is right around 12k to 15k and for the 2-1/2 inch…

view full answer...

Answer 3

The Stromberg Carlson Electric Trailer Jack #JET-5000 mentioned in your question is a great electric tongue jack that can lift and lower your trailer using its 12V motor with a total lift of 23 inches. It has a 5,000 pound lift capacity so it will…

view full answer...

Answer 4

If the bottom leg you are referencing on your Stromberg Carlson Electric Trailer Jack #JET-5000 is the foot pad, #2500-3755G, then we do have a replacement. If the bent leg is the tube that the jack foot goes into, that is not an available…

view full answer...

Answer 5

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Hi Emily, Before buying anything you'll want to verify that both the Pilot and the trailer hitch installed on it are rated for use with a weight distribution hitch (WDH). From what I can see Honda does not recommend it because it can shift the…

view full answer...

Answer 11

Hey Parvez, glad I could help! So the Rhino Rack Vortex Crossbars for Retrax XR tonneau covers part #RRVA180B-RRRLT600 was designed specifically to work with your RetraxOne XR tonneau cover so it is going to definitely have enough clearance above…

view full answer...

Answer 12

Thanks for the picture! The Curt TruTrack 2P Weight Distribution System w/ Sway Control item #C69JR will work with your 7,000 lbs Jayco 267BH. The Curt TruTrack has an 800 lbs to 1,000 lbs tongue weight range. The built in sway control will help to…

view full answer...

Hitch Pin Lock For A 2019 Toyota Tundra

Product Page this Question was Asked From

Continue Researching