Solution for Replacing Lock Cores in Thule Evolution Cargo Box

Question

Question:

My Thule Evolution pod worked great until this year - the locks will not open with my keys - I am supposing I need a locksmith to remove the lock cylinder - what do I need to replace the locks/keys and can I do it myself? Thank You

asked by: Jenn D

0

Expert Reply:

If the locksmith can get the lock core in the unlocked position you can use the change key that comes with the part # TH450200 to remove the old lock cylinder and then install the included cylinders that come with this kit and you'd be set.

expert reply by: Jameson C

0

Answer 1

Thule does not offer the lock housing or internal parts for the locks as replacement parts. If you are just missing the lock cores by themselves you can get a pair along with keys and the change key to install them using #TH450200.

view full answer...

Answer 2

The correct replacement key for your Thule Evolution Cargo Box is part #THKEYN042. The character after the N is actually a number zero, rather than a letter O, which look almost identical. So, unless you've got eagle-like vision, it's quite…

view full answer...

Answer 3

While we do not sell that exact replacement U-bolt for your Thule Mountaineer ES roof carrier, we do have a similar U-bolt that may work CE Smith U-Bolt - Galvanized #CE15283GA. This measures 4-5/16" long, has inner width of 3-1/16", and…

view full answer...

Answer 4

That's actually by design. Thule doesn't want you forgetting that the box is unlocked and then accidentally drive off and have the lid fly open and the contents go everywhere!

view full answer...

Answer 5

I went out to the warehouse and pulled replacement u-bolt #853-3105 to take some measurements. The width between the two ends is approximately 2-7/16 inches. The center to center distance though is 2-11/16 inches. The internal length is 3-1/2 inches…

view full answer...

Answer 6

The Replacement Lock Housing for Thule Snug Tite Hitch Lock #753-3725-02 is designed to replace the housing of the locks on of the Thule Snug Tite Hitch Lock and Anti-Rattle Device #THSTL2, so you're not going to be able to use this part on your…

view full answer...

Answer 7

We do offer replacement parts for your Sears X-Cargo 20-SV rooftop cargo box. For a set of 2 locks and 2 keys you can use part #SR03807. This will work if the locks look the same. There is a lock nut on the back of the lock assembly that will need to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Solution for Replacing Lock Cores in Thule Evolution Cargo Box

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching