Replacement Hitch Pin for Thule Vertex Bike Rack

Question

Question:

I need to replace the bolt that secures the bike carrier to the trailer hitch receptacle. The one I am replacing had a nut to tighten it down with, as well as a washer. The one that appears to be the replacement has a washer and a lock washer, but does not appear to have the nut. The bolt is a 12x40mm bolt. Will the nut that is included with this kit fit that bolt? Your website does not give the specs on the nut.

asked by: RICHARD W

0

Expert Reply:

The correct replacement hitch pin for a Thule Vertex bike rack is the part # TH62RE.

expert reply by: Jameson C

0

Answer 1

For your Thule Vertex XT you can use pin #TH62RE. This is the pin part only from the Snug-Tite lock you mentioned. This will allow you to have a regular threaded pin and add the lock later if you wanted.

view full answer...

Answer 2

I attached a picture that shows what the three different styles of wiper blades look like. Beam and Frame are the most different and Hybrid is mix of the two. The #MCH8519 is the hybrid style in the middle.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 6

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 7

All Thule bike racks use the same hitch pin, so you will want the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #853-5917 or the complete pin and lock kit #THSTL2. This is the 12mm thread you mentioned.

view full answer...

Answer 8

Thanks so much for the photos, they were very helpful, and based on that and the fact you mentioned it was from 2009, I am almost certain that what you have there is the Thule Roadway 914 bike rack. We do in fact have the correct 1-1/4" to…

view full answer...

Answer 9

From what I could find out about your current circuit board, the Atwood Replacement Control Panel #AT91367 will be a direct replacement.

view full answer...

Answer 10

Thank you for the picture. It looks like you have the Thule Hitching Post Pro, part #TH934XTR. We have a replacement bolt for that, but the bolt you reference, part #915087031, is not it. The replacement bolt you need comes in the Replacement…

view full answer...

Answer 11

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 12

The Thule T2 Pro XTR bike rack #TH83JV is designed to hold onto the tires of the bikes and not the frame so it would not be a good option for bikes with fenders or baskets. For a platform style bike rack that does have hooks that clamp down on the…

view full answer...

Replacement Hitch Pin for Thule Vertex Bike Rack

Product Page this Question was Asked From

Continue Researching