Availability of Replacement Fuse for Jensen TV Power Cord Adapter

Question

Question:

I need the fuse thats in the inside of the DCCIG09 TV Adapter Cord. The part number is F8AL Fuse. Also is it a 250V. I dont know what that means but it shows that 250V when I look up the F8AL F8AL250V

asked by: Kathy

0

Expert Reply:

I'm not sure what fuse is inside the Power Adapter Cord # DCCIG09 as Jensen doesn't have it available as a replacement part. The only solution we have would be for you to replace the whole thing.

expert reply by: Jon G

0

Answer 1

If you have power running to the unit but still can't get it to power on you may have a loose or blown fuse. The fuse of the Jensen RV Stereo - Single DIN - AUX/USB, Bluetooth, jControl - 12V #JWM70A is located on the rear of the unit by the…

view full answer...

Answer 2

When installing the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00 you can remove the fan housing if you like, and this will be easier if done from the top of the roof as opposed to inside the trailer. I have added…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Availability of Replacement Fuse for Jensen TV Power Cord Adapter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching