etrailer Hitch # e95ZR is Making Contact with my Rear Bumper Cover of my 2020 Hyundai Palisade
Question:
I received this hitch last week and got it installed yesterday. It does not fit the Palisade properly and is bending the plastic on the Bumper. It is not listed anywhere in the instructions that the bumper would need to be altered/cut into. I fear that if I leave this on it will do long term damage to the vehicle and warp the bumper.
asked by: Matt B
Expert Reply:
This is very common in hitches like the etrailer Hitch part # e95ZR. It is done to eliminate the need to trim the bumper cover and still get as much ground clearance as possible. It is likely that the bumper cover will get few blemishes on it since it is resting on it but this will not be an issue unless you decide to remove the hitch down the road. I recommend pushing the bumper cover back toward the front of the vehicle so it is gently resting on top instead of being bent rearward on the vehicle exaggerating the appearance.
As an alternative if you do not like the way it looks you can cut out the bumper cover around the hitch so it rest down and around the receiver tube opening instead of resting on top of it. This will have no ill effects on the hitches performance although it will alter the vehicle much more than if it were simply resting on top.
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: cu94fr
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Trailer Hitch Receiver & Wiring For 2024 Hyundai Palisade
- Shop: Roof Rack
- Q&A: Ground Clearance of the etrailer Hitch # e95ZR on a 2022 Hyundai Palisade
- Q&A: Will Trailer Hitches Fit a 2023 Hyundai Palisade XRT Model
- Shop: Brake Controller
- Video: WeatherTech HP Front Floor Mats Review
- Search Results: tk78vr
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Trailer Hitch For A 2023 Hyundai Palisade
- Shop: Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
- Q&A: Are You Required to Install a Wiring Harness on a 2022 Hyundai Palisade to Install a Hitch
- Video: Curt Spectrum Trailer Brake Controller Installation - 2020 Hyundai Palisade
- Q&A: Correct Trailer Hitch Fit for a 2023 Hyundai Palisade
- Video: etrailer Class III Trailer Hitch Installation - 2023 Hyundai Palisade
- Video: etrailer Class III Trailer Hitch Installation - 2022 Hyundai Palisade
- Q&A: Trimming Requirements For Draw-Tite Hitch # DT32RR On A 2023 Hyundai Palisade
- Video: etrailer Class III Trailer Hitch Installation - 2020 Hyundai Palisade
- Search Results: break controller
- Search Results: canoe
- Shop: Mud Flaps
- Shop: Suspension Enhancement
Matt B.
7/1/2020
Thanks for the reply, just a heads up there is no way to push it forward as it is already flush against the hitch.