Does Curt Hitch C13394 Fit 2019 Toyota Highlander

Question

Question:

Hi, I’m trying to decide on a hitch for my SUV. It’s a 2019 Toyota Highlander Hybrid Ltd Platinum. I’m looking at item # C13394 from Curt. 1. Is this hitch compatible? 2. What else do you recommend to purchase that would help with installation? Best regards,

asked by: Michael

0

Expert Reply:

The Curt hitch part # C13394 is a fit for your 2019 Toyota Highlander and is a great choice overall. It does not require anything else to install either as it comes with all of the needed hardware. It will allow you to keep your full-size spare as long as it is not on the aluminum rim. The aluminum rim is too wide for all of the compatible hitches for your 2019 Highlander.

I attached an install video for more info as well.

expert reply by: Jameson C

0

Michael

6/8/2020

Hi, I’ve installed my draw tite trailer hitch receiver and would like to put the driver side plastic panel back on. Do you have a template for cutting the panel that allows it to fit with the hitch receiver? Best regards, Michael

Reply

Chris R.

6/11/2020

Unfortunately we don't have a template available for trimming that panel. I really wish we did - your best option is to simply try and line it up to the vehicle to map out how much needs to be cut for re-installation. I would start small (since you can always trim more).

Reply

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Does Curt Hitch C13394 Fit 2019 Toyota Highlander

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching