Recommended Ball Mount for Curt Hitch On 2012 Kia Optima
Question:
Do you sell the adjustable ball mount/ or drawbar for the specific hitch below? I noticed the hitch is a class one. Many of the other adjujstable hitches are a class 3 or 4. Would the hitch and ball mount below be a proper fit together? -TRAILER HITCH Item# C11025 -ADJ. BALL MOUNT Item# MT70067
asked by: Amy D
Expert Reply:
The Curt Trailer Hitch Receiver part # C11025 is an excellent option for a 2012 Kia Optima. If you will be towing, you must use the Curt Drawbar part # C45521 as this is what Curt recommends. They also do not offer any adjustable ball mounts for class I hitches so there's that as well. I have attached some other parts below you might need as well.
Curt Class I and II Pin and Clip part # F-4
1-7/8" Hitch Ball part # A-80
Curt T-Connector Vehicle Wiring Harness part # C56314 or part # C56058 for EX or LX models
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Will Curt Hitch and Tekonsha Wiring Fit 2012 Kia Optima
- Q&A: Brake Controller Installation on a 2007 Ford Expedition with Factory 4-Way Wiring Harness
- Q&A: Aero Bar Roof Rack that Fits 2022 Toyota Highlander
- Article: Best Bike Racks for Electric Bikes
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Installing Brake Controller And Wiring On 2001 Ford Explorer Sport Trac
- Q&A: Brake Controller for 2019 Ford Edge With Factory Tow Package
- Q&A: Roof Rack and Cargo Basket Recommendation for 2015 Honda CR-V with Naked Roof
- Q&A: Will the Kuat Sherpa 2.0 2-Bike Platform Rack Block a Rear Backup Camera
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Hitch Receiver Sizes
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: What Do I Need To Tow A Trailer?