Choosing Correct Weight Distribution Shank

Question

Question:

I’m trying to figure out the correct WDH Shank to get to go with my new truck. Reese 113066 Hitch Head I have 2 different shanks. 1 is way to high and the other is too low/long. Also hoping to get a 2.5” to match the receiver for a change. What measurements are best to narrow it down? The hitch head is so tall, it throws me off.

asked by: Ryan S

0

Expert Reply:

To determine the amount of drop you'll need your replacement shank to have, take a height measurement from the top inside edge of the receiver tube to the ground, then measure from the bottom of the trailer's coupler to the ground (make sure trailer is level when taking the measurement) then subtract the coupler height from the hitch height. The result is the amount of drop you'll need.

We do offer weight distribution shanks for 2-1/2 inch receivers, and the hole spacing for the weight distribution head to mount is standard, so any of them will be compatible with the head used on your older Reese weight distribution system.

For a 1-1/4 inch drop, use # RP54976

2 inch drop, use # C17131

3 inch drop, use # EQ90-02-4700

4 inch drop, use # EQ90-02-4800

6 inch drop, use # EQ90-02-4900

9-1/4 inch drop, use # C17132

expert reply by: Mike L

0

click to enlarge

Answer 1

When choosing a weight distribution system, you want to go off the total tongue weight. This total tongue weight includes the loaded weight of the trailer tongue that you stated along with any cargo behind the rear axle of the towing vehicle. As long…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Choosing Correct Weight Distribution Shank

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching