Correct Hott Rod RV Water Heater Conversion Kit for 6 Gallon Water Heater

Question

Question:

Will this work in a 6 gal water heater?

asked by: David

0

Expert Reply:

The correct Hott Rod RV Water Heater Conversion Kit for a 6 gallon water heater is part # DGR6VP, the part # DGR10VP is for 10 gallon water heaters and would be too powerful for a 6 gallon.

expert reply by: Conner L

0

Answer 1

The Hott Rod RV Water Heater Conversion Kit #DGR6VP does fit your Atwood GC6AA-8 (AT96117) Water Heater. It installs into the drain plug after you remove it. It comes with an adapter to allow it to thread into the water heater. It will be just as…

view full answer...

Answer 2

The cable for the Hott Rod RV Water Heater Conversion Kit #DGR6VP is removable from the Heating Element #DGR6P2PB. You will simply pull the end of the cable off the heating element when you need to remove it for draining your water heater.

view full answer...

Answer 3

I have a possible solution for carrying your KTM. The Ultra-Fab Motorcycle Carrier, part #UF48-979033 would be a good bargain-priced option. The carrier has a 500 lb capacity and the ramp is included. This carrier is only compatible with hitches…

view full answer...

Answer 4

When turning your Atwood/Dometic G6A-8E water heater from propane to electric you will need The Hott Rod RV Water Heater Conversion Kit #DGR6VP. This conversion kit converts your RV's propane water heater to electric operation, while keeping…

view full answer...

Answer 5

We carry a few different types of Locking Cam with Keys that could work for your application. The Cam Lock Cylinder with Key, #295-000003, can replace 7/8 of an inch long cam. The attached link will display all the locking style cams and the…

view full answer...

Answer 6

If you are only wanting to replace the cylinder you need the Replacement Thumb Turn Cam Latch Cylinder - Stainless Steel - 1-1/8" Long Item #295-000012. If you are wanting to replace the whole latch you need the replacement thumb latch you…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Correct Hott Rod RV Water Heater Conversion Kit for 6 Gallon Water Heater

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching