Who Makes the Replacement Trailer Hub Bearing L68149

Question

Question:

Can you please tell me who manufacturers the L68149 bearings.

asked by: Matt

0

Expert Reply:

The Replacement Trailer Hub Bearing part # L68149 like most trailer bearings if not all are manufactured overseas. This particular bearing is made by AxleTek. We have been using these trailer bearings for quiet some time and have heard nothing but good things in regards to their performance and longevity.

expert reply by: Conner L

0

Answer 1

Trailer tires are generally rated for a maximum speed of 65 mph. This is true for both radial and bias ply types. The tire diameter does not have a direct relationship to its speed rating. What is most important for any trailer tire is that it be…

view full answer...

Answer 2

Thank you for your purchase of the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel #AM3H440. We recommend using the PSI rating of 70 which is listed on the sidewall of the tire. Some tire manufacturers have a progression chart…

view full answer...

Answer 3

The Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel #AM3H430 features a 10 inch steel wheel that uses 1/2"-20 wheel bolts. With this in mind you will want to torque the bolts between 75 and 85 foot pounds. I have attached a lug nut…

view full answer...

Answer 4

Excellent question. There is no disadvantage to using a special trailer tire with a higher weight Load Range Rating than is required by your trailer's weight. Doing so simply means that those higher-rated tires will tend to run cooler, since they…

view full answer...

Answer 5

Special trailer tires should be inflated to their maximum air pressure. At the maximum air pressure, the tires will perform and wear best, and get the best gas mileage. The Kenda 205/65-10 Bias Trailer Tire #AM3H430 has a maximum load carrying…

view full answer...

Answer 6

I can confirm for you that the speed rating of the Loadstar K399 Bias Trailer Tire #AM1HP54 that is on the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel - 5 on 4-1/2 - Load Range D #AM3H430 is indeed 81 mph.

view full answer...

Answer 7

Your spindle dimensions match very closely to what we have hubs for but the inner bearing dimension would need to be 1.380 and not 1.480 inches. The outer bearing dimension needs to be 1.06 and the seal dimension 1.73 inch. If that is the case for…

view full answer...

Answer 8

To ensure that you get a hub that fits your spindle correctly you will want to use a digital caliper and measure points B, C, and D (see attached picture) of your spindle to the 3rd decimal place, for example 1.750. These measurements will help us to…

view full answer...

Answer 9

The #168233 Double Lip Grease Seal has an outside diameter of 2.332 inches and an inside diameter of 1.688 inches. This seal is not compatible with a AF2527E seal with a O.D 2.312, because, even though the O.D. id very close, the inner diameter of…

view full answer...

Answer 10

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 11

I wish I could tell you based off of the picture you sent in what bearings work with your spindle but if you don't have numbers on your bearings then the next best thing is to take a digital caliper and measure where each of the bearings and the…

view full answer...

Answer 12

If your trailer was made after 1978 then the VIN will be 17 characters long. The VIN you provided 1ZEAAZRT64A01001 is only 16 characters long. I cannot determine the bearing numbers unless I have the full accurate VIN of your trailer. If you instead…

view full answer...

Who Makes the Replacement Trailer Hub Bearing L68149

Product Page this Question was Asked From

Continue Researching