How Much Rise is Needed when Using Draw-Tite Trailer Hitch for 2014 Dodge Grand Caravan
Question:
How do I determine whether to buy a 2inch or 4inch / riser ?
asked by: Mike B
Expert Reply:
Are you trying to find out if the ball mount you get needs to have a 2 or 4 inch rise when using the Draw-Tite hitch # 75579 on your 2014 Dodge Grand Caravan? If that's the case and you already have the hitch and trailer you just need to take a couple measurements and find the difference between them.
With both the van and the trailer parked on level ground measure from the top of the hitch's receiver opening to the ground and from the bottom of the trailer's coupler to the ground. The difference between these is the amount of rise you need in a ball mount if the trailer's measurement is more than the van's. If it's the other way around you need a drop.
When we installed the Draw-Tite on a 2014 Grand Caravan it measured 13-1/2 inches. Yours could be different depending on the wear on the van but it'll likely be very close. If you don't already have the hitch you can use our measurement and you'll have a really good idea on yours.
If you find you need either a 2 inch or a 4 inch such as part # C45270 or part # D-28 I've linked both of those selections we carry for you that'll fit the hitch. I've linked our complete selection of ball mounts that fit too.
Products Referenced in This Question
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Long Shank
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What Trailer Hitch Fits a 2019 Dodge Grand Caravan with Stow-N-Go Seats
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Trailer Hitch and Towing Capacity for 2018 Dodge Grand Caravan
- Q&A: Rise or Drop of Ball Mount Needed for 2016 Dodge Grand Caravan
- Q&A: Is There a Hidden Receiver Available for a 2023 Chevrolet Equinox Which Fits Behind Factory Cover?
- Q&A: Difference Between the Draw-Tite and EcoHitch Trailer Hitches for a 2023 Tesla Model Y
- Q&A: Trailer Hitch Recommendation for 2016 Dodge Grand Caravan
- Article: Which Hitches are Made in the USA
- Article: Trailer Maintenance Schedule