Replacement Strut for Solera Awning With 69 Inch Arms

Question

Question:

I have a Solera awning 69inch My Gas strut broke Which is the right part so I can buy it thanks

asked by: Yanelly S

0

Expert Reply:

The correct replacement strut for your Solera Awning with 69" arms is the Solera Gas Strut 26" part # LC280343 which I confirmed with Lippert for you.

expert reply by: Conner L

0

Answer 1

I have a solution for you but we do not carry an exact replacement for the 654150 0550N 091/16 strut . The strut we carry that is almost the same is the Solera Gas Strut for Short and Flat Awning Arms item #LC280343 that you were looking at. The…

view full answer...

Answer 2

Since the ends of the Solera Gas Strut 26 #LC280343 are not replaceable you'd have to go with the #LC280343 to get the parts you need as well as new struts.

view full answer...

Answer 3

The Solera Gas Strut 26", 124 lbs for Short and Flat Awning Arms #LC280343 attaches between awning arms via pins, which go through the opening on the two ends of the strut. According to the manufacturer, the openings on the strut are 3/8",…

view full answer...

Answer 4

Though we don't carry that exact part, we do have a strut with the same dimensions that is likely to work. Based on my research the gas strut 654150 is 26.46" when extended, has two metal ends and is 120 lbs of force. The strut we carry…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Replacement Strut for Solera Awning With 69 Inch Arms

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching