Do Running Boards from Extended Cab 2010 Chevy Silverado also Fit Crew Cab

Question

Question:

WILL 2010 EXT CAB BOARDS FIT 2010 CREW CAB?

asked by: PAUL

0

Expert Reply:

Since running boards run the length of the cab the different cab styles all require different length running boards. This means that extended cab running board fits won't work with crew cab. The # 23-1955 that you referenced will fit the crew cab models of a 2010 Chevy Silverado though. I attached and install video for this board set for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Trucks like yours that have suspension designed for heavy towing loads have the unfortunate side effect of being feeling pretty rough over bumps when not loaded. The easiest solution is to add weight in the bed of the truck which allows the…

view full answer...

Answer 2

It depends on what running boards you are talking about. For instance, the Westin E-Series Round Nerf Bars - 3" - Black Powder Coated Steel #23-1955 will fit a 2008-2013 Silverado 1500 Crew Cab and a 2014 2500 or 3500 Crew Cab. Let me know…

view full answer...

Answer 3

If the U-bolts are 9/16 inch diameter, the torque specs should be between 65 to 95 foot lbs. If the U-bolts are 3/8 inch diameter, the torque should be between 30 and 50 foot lbs.

view full answer...

Answer 4

In 2014 the 1500 series of Silverados had a generation change so a set of running boards from a 2003 would not fit a 2014. The part #23-1955 would fit the 2003 model you have though.

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Do Running Boards from Extended Cab 2010 Chevy Silverado also Fit Crew Cab

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching