Parts Needed to Move Curt Q20 from 2015 GMC to 2020 GMC With OEM Prep Package

Question

Question:

I currently have a curt q20 in my 2015 Gmc 3500 duramax. Wondering if there is a way to adapt it my 2020 gmc duramax? If what would be the cost? Thx

asked by: Ernest R

1

Helpful Expert Reply:

To move the Curt Q20 fifth wheel hitch head from your 2015 GMC 3500 to the factory pucks of your 2020 use part # CU53FR. This then gives you the complete Q20 hitch for the new GM puck system which is part # C57FR

expert reply by: Patrick R

1

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

Hi David, Rock Tamers require an inch of space on the ball mount shank in order to mount. If the portion of the shank exposed where you'll be installing the Rock Tamers is 2" x 2" then you'll want #ERT00108, for 2.5" x…

view full answer...

Answer 5

To flat tow a 2024 GMC Sierra 2500 you will need the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Direct-Connect Base Plate item #e84ZR Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms…

view full answer...

Answer 6

There are a select few fifth wheel hitches that have replacement leg kits that would adapt them to fit the OEM prep package of your Dad's 2023 GMC Sierra 3500 but I would need to know what hitch you guys have to be able to determine if that's…

view full answer...

Answer 7

Hi Robert, To install your Putco Blade LED Tailgate Light Bar #P22KR you'll need to just remove the tail lights so that you can get access to the back wiring in the back of them. The plug-and-play connectors on the wire harness with have a male…

view full answer...

Answer 8

Hi Chris, Yes, the Demco LED Light Bar for Towed Vehicles w/ Wireless Transmitter #DM36MV is approved and legal for flat towing your vehicle. It's designed to attach to the rear window with a suction cup and face rearward so that others on the…

view full answer...

Answer 9

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

We can get your 2024 Chevy Silverado 1500 4x4 set up with a complete system for flat towing, and I'll go ahead and list out all the parts you need to make it easy to order: - Base Plate Kit: Roadmaster Direct-Connect Base Plate Kit #RM86MR - Tow…

view full answer...

Answer 12

For you 2024 GMC Sierra 2500 AT4 that has a 3 inch lift I would go with the Roadmaster sway bar part #RM25FR as it's slightly thicker than the Hellwig that also fits your truck which will be helpful since lifted vehicles have a higher center of…

view full answer...

Parts Needed to Move Curt Q20 from 2015 GMC to 2020 GMC With OEM Prep Package

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching