Are Replacement Parts Available for the Buyers Products 12v Electric 3500-lb Camper Jack?

Question

Question:

can I replace the leg on the buyers 3500 camper jack? It bent when I didnt raise the leg when I drove forward, If so where would I purchase a new leg?

asked by: Hugh H

0

Expert Reply:

You can replace the leg on the Buyers Products 12v Electric Jack # 3370093500 with the Replacement Footpad for Buyers Products 12v Electric Jacks # 3373013261 .

expert reply by: Erik B

0

Answer 1

I do have a solution for you, however the Replacement Foot Pad #2500-3755G referenced in your question is designed specifically for certain electric jacks made by Stromberg Carlson so I cannot confirm if it will work well for your existing jack.…

view full answer...

Answer 2

I pulled up pictures of your 2012 Travel Lite Idea 15q and the Lippert Jack-It bike rack part #LC429756 would fit and work great.

view full answer...

Answer 3

The Replacement Foot for etrailer or Ram Electric Jacks #EJ-3520-FT has an inner diameter of about 1-1/2" and its outer diameter is 1-3/4" which is the measurement you'll need if you are looking for a replacement. This foot…

view full answer...

Answer 4

The footplate/drop-leg is indeed removeable on the etrailer.com Electric Jack w/ Footplate - A-Frame - 25-1/2" Lift - 3.5K - Black #e49ZR. Said footplate ( #EJ-3520-FT ) is held in place with a snapper style pin ( #JFC-PN ), both of which…

view full answer...

Answer 5

Sounds like you have an issue with the nut and screw of the inner leg on your trailer jack. Typically this is a sign that it's time to replace the jack as it has an internal problem. I recommend replacing it with the Stromberg Carlson Electric…

view full answer...

Answer 6

The outer diameter of this tube is 1-3/4 inches, if that matches the diameter of your old foot, this should work well for you. A snapper pin like #2500-26 is typically used to hold the foot in place.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Are Replacement Parts Available for the Buyers Products 12v Electric 3500-lb Camper Jack?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching