Will Draw-Tite Class II Receiver Hitch # 36548 Fit a 2011 Dodge Charger R/T
Question:
Will this hitch fit on my 2011 Dodge Charger R/T?? Thanks
asked by: Josh
Expert Reply:
Any of the hitches we offer for the 2011 Charger will fit most models, including the R/T model. We have found that installing the hitch on dual exhaust models involves temporarily removing the muffler on the drivers side. On models that have dual exhaust tips on each side (for a total of 4), the muffler will be welded, instead of being clamped into place. This makes removing the muffler impossible, therefore the hitch CANNOT be installed.
If your Charger only has the single exhaust tip on each side of the vehicle, the Draw-Tite # 36548 you mentioned will work fine for you.
If you are planning on towing with your Charger, you might also need the following to complete your towing system:
Trailer wiring harness with 4-pole connector, # 118560
Ball mount, # 36061
1-7/8 inch trailer ball, # 19256
2 inch trailer ball, # 19258
To see the hitch install details, click on the provided link.
![Mike L](https://images.etrailer.com/static/images/catg/people/166_tn.jpg)
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Recommendation For Trailer Hitch Mostly Hidden On 2014 Dodge Charger
- Q&A: Trailer Hitch Recommendation for 2016 Dodge Charger R/T Scat Pack to Carry Thule Vertex 4 Bike Rack
- Q&A: Recommended Trailer Hitch for a 2015 Dodge Charger
- Article: What Jeeps Can Be Flat Towed?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Scissor Jack Recommendation to Replaced Damaged Ones on R Pod Trailer
- Q&A: Will the Trailer Hitch for a 2019 Dodge Challenger Work with Aftermarket Exhaust
- Q&A: Why Is 5th Wheel Trailer Clunking When Starting/Stopping with B&W Companion and MORryde Pin Box
- Q&A: Determining if 2014 Ford F-250 Has OEM Rail Kit for B and W Gooseneck Hitch
- Article: Trailer Wiring Diagrams
- Article: What Do I Need To Tow A Trailer?
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: Best Bike Racks for Electric Bikes