What Needs to be Trimmed to Install etrailer Hitch on 2018 Honda CR-V

Question

Question:

In the directions that came with the E98848 the diagram indicates that you need to cut a section of the fascia that is 3inch by 1.375. In the answer to a previous question on this site it seemed to indicate that a 3inch by 3inch cut needed to be made, In either case I am confused as to the reference point for the 1.375inch or 3inch as the case may be. Is it a distance measured vertically? Is it measured from the leading edge of the fascia? Or something else?

asked by: David B

0

Expert Reply:

The 3 inch dimension that needs to be cut from the rear bumper to install the etrailer.com hitch part # E98848 that you referenced is measured from the edge of the fascia and matches the angle of it. So the square cut would measure 3 inches. If you were to cut it 3 inches vertically when you measured on the fascia and matched the angle of it the cut would be much longer.

For more info on this check out the install video I attached as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, we have since been able to confirm the etrailer Trailer Hitch Receiver part #e98848 will fit a 2021 Honda CR-V Hybrid after some confusion early on. There have been multiple reviews from our customers stating it was compatible. I have attached…

view full answer...

Answer 2

Fascia trimming is required to install the etrailer Trailer Hitch Receiver #e98848 on your 2024 Honda CR-V, but this is the case for all of the hitches that fit your vehicle. According to the instructions you'll be cutting out a notch that…

view full answer...

Answer 3

We have great hitches that fit your 2021 Honda CR-V hybrid like with the part #e98848. This hitch does not void the warranty of the vehicle in any way. I attached an install video link for this as well. If you were in need of trailer wiring too the…

view full answer...

Answer 4

I recommend the etrailer Trailer Hitch Receiver, #e98848. This is a custom fit Class III, with a 2"x2" receiver opening that is rated at a full 525 lbs. tongue weight and protected with a matte black finish for added durability.…

view full answer...

Answer 5

To trim the fascia on your 2021 Honda CR-V to allow the etrailer Trailer Hitch Receiver #e98848 fit our installers have found a dremel is the best option as it allows for a very precise cut and is easy to use. You can see Conner using a dremel at…

view full answer...

Answer 6

The Draw-Tite Trailer Hitch #DT79MR will not fit the Hybrid model of your 2021 Honda CR-V, but you can use the etrailer Trailer Hitch #e98848 instead. This has the same basic design as the Draw-Tite hitch you were looking at so that only the hitch…

view full answer...

Answer 7

We have the etrailer hitch part #e98848 which is a confirmed fit for your 2020 Honda CR-V hybrid. I attached a picture of it installed on a hybrid CR-V for you to check out as well.

view full answer...

Answer 8

Hitch bike racks including those from Thule and Yakima are made to fit either a 1-1/4-inch hitch, a 2-inch hitch or based or their design sometimes both sizes. To illustrate, Thule hitch racks for both hitch sizes are shown on the linked page. The…

view full answer...

Answer 9

Some trimming of the rear fascia on your 2020 Honda CR-V is indeed required when installing the etrailer Trailer Hitch Receiver #e98848 to allow clearance for the drop-down receiver. You will just need to use some shears/snips to trim about…

view full answer...

Answer 10

Yes, the etrailer Trailer Hitch Receiver part #e98848 which is what I recommend, is a confirmed fit for a 2023 Honda CR-V Hybrid Sport Touring. It also has a 2" opening so it will be great for towing or other hitch mounted accessories like…

view full answer...

Answer 11

There are indeed two 2" trailer hitches available for your 2020 Honda CR-V; the etrailer #e98848 and the Curt #C13397. These Class III hitches are essentially identical in every way except for the finish/powder coat that they use. I…

view full answer...

Answer 12

The etrailer Trailer Hitch Receiver #e98848, Curt Trailer Hitch Receiver #C13397, and EcoHitch Hidden Trailer Hitch Receiver #306-X7345 for your 2017 Honda CR-V Touring AWD will all be equally hidden with just the receiver itself being visible as…

view full answer...

What Needs to be Trimmed to Install etrailer Hitch on 2018 Honda CR-V

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching